718499
13
Zoom out
Zoom in
Previous page
1/16
Next page
HELPFUL HINTS
Error message What to do when...
Troubleshooting
6
Message Cause/Remedy
Battery Low! The batteries are low.
If using AAA alkaline batteries: Replace them
with six new AAA alkaline batteries. Do not use
old and new batteries together or mix alkaline
batteries with other battery types.
If using Ni-MH batteries: Charge them fully.
Battery Empty! The installed batteries are running low and
need to be changed for continued operation.
Invalid! • There is no text above the cursor when you
selected [Numbering].
• You selected an invalid character for
[Numbering].
• You selected an invalid number for [Label
Length].
• You entered an invalid value as the label
length while using templates.
No Text! You tried to print a text file when there is no
data stored in the memory.
You pressed when no text is entered.
You pressed + when no text is
entered.
You pressed when no text is entered.
Do not press or when no text was
entered while using templates.
2 Line Limit!/
1 Line Limit!
• Make sure you do not exceed the maximum
number of lines allowed (two).
• You tried to print or preview two lines of text
while 3.5 or 6 mm tape is installed. Install a
larger tape size.
No Cassette! You tried to print, feed or preview a label when
there is no cassette installed.
Cutter Pressed You pressed the tape cutter lever in the middle
of the printing process.
Text Full! Make sure you do not exceed the maximum
number of characters allowed (80 characters
for text, 50 characters for templates. If your
message contains symbols, the maximum
number of characters may be reduced.).
Text Limit!
Change Length
Since the number of entered characters
exceeds the label length, reduce the text, or
select [Auto] as the label length.
No Frame OK? • Printing on 3.5 mm tape with invalid Frame
setting ON.
(Select to print with no Frame,
to cancel.)
Feed OK? Feeding tape after printing when [Chain Print]
is selected. See “Setting Margin”.
Insert 12 mm • Only 12 mm tape cassette is available for
templates.
Wrong Tape!
Use TZe tape
• Use a tape cassette with the mark.
Problem Solution
The display
stays blank
after you have
turned on the
machine.
Check that you installed the batteries with the
positive and negative ends in the correct
position.
• If the batteries are low, replace them with six
new AAA alkaline batteries. Do not use old
and new batteries together or mix alkaline
batteries with other battery types.
• Check that you connected the AD-24ES
adapter correctly.
When the label
is printed out,
there is too
much margin
(space) on both
sides of the text.
See “Setting Margin” in this user's guide and
select [Half] or [Narrow] to have smaller
margins for your label.
The machine
does not print,
or the printed
characters are
not formed
correctly.
• Check that you have inserted the tape
cassette correctly.
• If the tape cassette is empty, replace it.
• Check that you closed the cassette cover
correctly.
The machine's
settings have
reset
themselves.
The batteries may be low. Replace them with
six new AAA alkaline batteries. Do not use old
and new batteries together or mix alkaline
batteries with other battery types.
• When power is disconnected for more than
three minutes, all text and formats in the
display are lost.
A blank
horizontal line
appears
through the
printed label.
There may be some dust on the print head.
Remove the tape cassette and use a dry cotton
swab to gently wipe the print head with an up-
and-down motion. The optional print head
cleaning cassette (TZe-CL3) is also available.
The machine
has “locked up”
(that is, nothing
happens when
a key is
pressed, even
though the
machine is on.)
See “Resetting the machine”.
The power
turns off when
you try to print.
The batteries may be low. Replace them with
six new AAA alkaline batteries. Do not use old
and new batteries together or mix alkaline
batteries with other battery types.
• Check that you inserted the batteries
correctly.
• A wrong adapter is used; the recommended
adapter is the AD-24ES.
The tape does
not feed
correctly or the
tape gets stuck
inside the
machine.
• Check that the end of the tape feeds under
the tape guides.
• The cutter lever is pressed while printing. Do
not touch the cutter lever during printing.
To change the
language
setting.
See "Initial Settings".
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother P-Touch H110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother P-Touch H110 in the language / languages: English as an attachment in your email.

The manual is 19,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother P-Touch H110

Brother P-Touch H110 User Manual - German - 18 pages

Brother P-Touch H110 User Manual - Dutch - 16 pages

Brother P-Touch H110 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info