Manual Brother P-Touch D210 (page 6 of 8) (English)

718500

6

Zoom out

Zoom in

Previous page

1/8

Next page

 Error messages  What to do when...

Troubleshooting

Message Cause/Solution

Battery Low! The batteries are running low.

If using AAA alkaline batteries: Replace them

with new ones.

If using Ni-MH batteries: Charge them fully.

Battery Empty! The installed batteries are running low and

must be changed for continued operation.

Invalid! • There is no text above the cursor when you

select [Numbering].

• An invalid character is selected for [Numbering].

• An invalid number is selected for [Tab Length]

or [Label Length].

• An invalid value was entered as the label

length while using templates.

No Text! • No data in memory to print a text file.

• is pressed when no text is entered.

• + is pressed when no text is

entered.

•

is pressed when no text is entered.

• or was pressed when no text

was entered while using templates.

2 Line Limit! /

1 Line Limit!

• Cannot enter a third line by pressing .

• Cannot print or preview two lines of text while

3.5 mm or 6 mm tape is installed. Use a larger

tape size.

No Cassette! Install a cassette to print, feed or preview a

label.

Cutter Pressed The tape cutter lever has been pressed in the

middle of the printing process.

Text Full! The maximum number of characters

(80 characters for text, 50 characters for

templates) exceeded.

Change Length Since the number of entered characters

exceeds the label length, reduce the text, or

select [Auto] as the label length.

No Frame OK? • Printing on the 3.5 mm tape with an invalid

Frame setting ON.

• Make sure you use the 12 mm wide tape

cassette.

(Select to print with no Frame,

to cancel.)

Feed OK? • Feeding tape after printing when [Chain Print]

is selected. Refer to “Set Margins”.

Insert 12 mm • Use the 12 mm tape cassette designed for

templates.

Use TZe Tape!

• Use a tape cassette with the mark.

Problem Solution

The display

stays blank

after you have

turned the

machine on.

• Check that the batteries are correctly

inserted.

• If the batteries are running low, replace them.

• Check that the AD-24ES adapter is correctly

connected.

The machine

does not print,

or the

characters are

printed

incorrectly.

• Check that the tape cassette has been

inserted correctly.

• If the tape cassette is empty, replace it.

• Check that the cassette cover is closed

correctly.

The setting has

cleared on its

own.

• If the batteries are running low, replace them.

• When power is disconnected for more than

three minutes, all text and formats in the

display will be lost.

A blank

horizontal line

appears

through the

printed label.

• There may be some dust on the print head.

Remove the tape cassette and use a dry

cotton cloth to carefully wipe the print head

with an up-and-down motion.

The machine

has “locked up”

(nothing

happens when

a key is

pressed, even

though the

machine is on).

• Refer to “Resetting the P-touch”.

The power

turns off when

you try to print.

• If the batteries are running low, replace them.

• Check that the batteries are correctly

inserted.

• A wrong adapter is used; the recommended

adapter is AD-24ES.

The tape does

not feed

correctly or the

tape gets stuck

inside the

machine.

• Check that the end of the tape feeds under

the tape guides.

• The cutter lever is pressed while printing. Do

not touch the cutter lever during printing.

All text and

format settings

need to be

cleared to

create a new

label.

• Press + and select

[Text&Format].

• Press / [Clear]

/ [Text&Format]

To change

language

setting.

• Refer to “Initial Setup”.

TIPS

Tip 1 To reduce the margin on printed labels

See “Set Margins”. By selecting the Chain Print

option, the margin can be reduced to a minimum

when printing multiple labels with alternate text.

Tip 2 When the LCD is difficult to see

See “LCD Contrast Adjustment” and change the

setting.

Be sure to remove the protective sticker placed over

the LCD at the time of product shipment.

You can reset the P-touch labeller to revert to the

factory settings, or if the labeller is not working

correctly. All text, settings and stored files are cleared.

1 Turn off the P-touch labeller, press and hold

and , and then press to turn the

P-touch labeller back on.

2 First release the power button, and then

release and .

The P-touch labeller turns on with the internal

memory reset.

NOTE

Shortcuts

File

Tab

Unit

LCD Contrast

Clear

Language

Common Operations

Clear

Feed

Print Options

Narrow

Chain Print

5

(Space key)

ABC

DEF

GHI

DEF

ABC

GHI

Resetting the P-touch

CAUTION

USING A COMBINATION OF DIFFERENT

BATTERIES (SUCH AS Ni-MH AND ALKALINE), MAY

RESULT IN AN EXPLOSION. DISPOSE OF USED

BATTERIES ACCORDING TO THE INSTRUCTIONS.

Battery Recommendations

• Remove the batteries if you do not intend to

use the P-touch labeller for an extended

period of time.

• Dispose of the batteries at an appropriate

collection point, not in the general waste

stream. In addition, be sure to observe all

applicable local regulations.

• When storing or discarding the batteries, wrap

them (for example with cellophane tape) to

prevent them from short-circuiting. (Refer to

the illustration below)

(Battery insulation example)

1. Cellophane tape

2. Alkaline or Ni-MH

battery

2

1

1

Bonsoir, je n'ai pas trouvé dans le manuel Brother 210, l'explication comment écrire sur une étiquette dans le sens de la hauteur. A fin de la collée au dos d'un livre. Submitted on 19-4-2022 at 21:00
Reply Report abuse
Bonsoir, je n'ai pas trouvé dans le manuel, comment imprimer une étiquette dans le sens de la hauteur pour mettre au dos d'un livre.
Bonne soirée. Submitted on 19-4-2022 at 20:53
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Brother P-Touch D210 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother P-Touch D210 in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother P-Touch D210

Brother P-Touch D210 User Manual - German - 8 pages

Brother P-Touch D210 User Manual - Dutch - 8 pages

Brother P-Touch D210 User Manual - French - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info