463656
144
Zoom out
Zoom in
Previous page
1/164
Next page
TROUBLESHOOTING
142
TROUBLESHOOTING
If you have a minor problem with your sewing machine, check the following solutions. If the solutions suggested do
not correct the problem, contact your authorized dealer.
Memo
This machine is equipped with a simple troubleshooting feature that can be used in case minor problems occur during
sewing. Press , and then press to display a list of problems. Press the key for the
appropriate problem, and then check for the causes that are displayed.
Problem Cause Solution Page
Upper thread breaks The machine was threaded incorrectly (the spool
is installed incorrectly, the wrong spool cap was
used, the needle bar thread guide did not catch
the thread, etc.).
Rethread the machine correctly. 27
The thread is knotted or tangled. Remove the knots and tangles.
The thread is too thick for the needle. Check the table of fabric, thread and needle
combinations, and select the appropriate
combination.
35
The upper thread tension is too strong. Adjust the thread tension. 43
The thread is tangled. Use scissors, etc., to cut the tangled thread and
remove it from the race (bobbin case), etc.
The needle is bent or blunt. Replace the needle with a new one. 33
The needle is installed incorrectly. Reinstall the needle correctly. 33
There are scratches around the hole in the
needle plate.
Replace the needle plate, or consult your
authorized dealer.
There are scratches around the hole in the
presser foot.
Replace the presser foot, or consult your
authorized dealer.
There are scratches on the race (bobbin case). Replace the race (bobbin case), or consult your
authorized dealer.
Bobbin thread breaks Bobbin is set incorrectly. Reset the bobbin correctly. 26
There are scratches on the bobbin or it doesn’t
rotate properly.
Replace the bobbin.
The thread is tangled. Use scissors etc., to cut the tangled thread and
remove it from the race (bobbin case), etc.
Skipped stitches The machine is threaded incorrectly. Check the procedure for threading the machine
and rethread it correctly.
27
The thread or needle is not suitable for the type
of fabric being sewn.
Check the table of fabric, thread and needle
combinations, and select the appropriate
combination.
35
The needle is bent or blunt. Replace the needle with a new one. 33
The needle is installed incorrectly. Reinstall the needle correctly. 33
The needle is defective. Replace the needle. 33
Dust or lint has collected under the needle plate. Remove the dust or lint with the brush. 138
Fabric puckers The upper or bobbin threading is incorrect. Check the procedure for threading the machine
and rethread it correctly.
26, 27
The spool is installed incorrectly. Reinstall the spool correctly. 27
The thread or needle is not suitable for the type
of fabric being sewn.
Check the table of fabric, thread and needle
combinations, and select the appropriate
combination.
35
The needle is bent or blunt. Replace the needle with a new one. 33
The stitches are too long for sewing lightweight
fabrics.
Shorten the stitch length. 42
The thread tension is set incorrectly. Adjust the thread tension. 43
The wrong presser foot was used. Attach the correct presser foot. 151
144


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother NX-2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother NX-2000 in the language / languages: English as an attachment in your email.

The manual is 10,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother NX-2000

Brother NX-2000 User Manual - German - 164 pages

Brother NX-2000 User Manual - Dutch - 164 pages

Brother NX-2000 User Manual - French - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info