Manual Brother MFC-990CW (page 37 of 47) (English)

451233

Zoom out

Zoom in

1/47

Start Here

MFC-790CW

MFC-990CW

Quick Setup Guide

UK/IRE/GEN/SAF Version 0

Before you can use the machine, read this Quick Setup Guide for the correct setup and installation.

Unpack the machine and check the components

WARNING

Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep

these bags away from babies and children.

 Illustrations in this Quick Setup Guide are based on MFC-790CW.

a Remove the protective tape and film covering the scanner glass.

b Remove the green protective packing a by lifting the front of the

machine and then pulling down on the packing part.

Remove the plastic bag

containing the ink cartridges from on top of

the paper tray.

d Make sure you have all components.

WARNING Warnings tell you what to do to prevent possible personal injury.

Important

DO NOT connect the USB cable yet (if you are using a USB

cable).

Inbox Ink Cartridges

[x4]

Black

Yellow

Cyan

Magenta

(Approx. 65% yield of the

replacement cartridge) For

details, see Consumable

items in the User

’s Guide.

Quick Setup Guide

User’s Guide CD-ROM Power Cord Telephone Line Cord

Telephone Handset

(MFC-790CW only)

Side Cover

(MFC-790CW only)

Cordless Handset

(MFC-990CW only)

Battery and Battery Cover

(MFC-990CW only)

User’s Guide for Cordless Handset

(MFC-990CW only)

d Fan the stack of paper well to avoid paper jams

and misfeeds.

e Gently put the paper into the paper tray print

side down and top edge first. Check that the

paper is flat in the tray.

f Gently adjust the paper side guides to the

paper with both hands. Make sure that the

paper side guides touch the edges of the

paper.

g Close the paper tray cover a.

h Slowly push the paper tray completely into the

machine.

i While holding the paper tray in place, pull out

the paper support a until it clicks, and then

unfold the paper support flap b.

Important

Do not push the paper in too far.

Connect the power cord

and telephone line

a Connect the power cord.

WARNING

The machine must be fitted with an earthed

plug.

b Connect the telephone line cord. Connect one

end of the telephone line cord to the socket on

the machine marked LINE and the other end to

a telephone wall socket.

WARNING

Since the machine is grounded through the

power outlet, you can protect yourself from

potentially hazardous electrical conditions on

the telephone network by keeping the power

cord connected to your machine when you

connect it to a telephone line. Similarly, you

can protect yourself when you want to move

your machine by disconnecting the telephone

line first and then the power cord.

Important

DO NOT connect the USB cable yet (if you are

using a USB cable).

Important

The telephone line cord MUST be connected

to the socket on the machine marked LINE.

Note

If you are sharing one telephone line with an

external telephone, connect it as shown below.

1 Extension telephone

2 External telephone

Please make sure you use an external telephone

with a cable no more than 3 metres long.

Note

If you are sharing one telephone line with an

external telephone answering machine, connect it

as shown below.

Set the receive mode to Manual if you have

an external answering machine. See

Choose a Receive Mode on page 7. For

additional details, see Connecting an

external TAD (telephone answering device)

in Chapter 7 of the User’s Guide.

Install the ink cartridges

WARNING

If ink gets in your eyes, wash them out with

water at once, and if irritation occurs consult a

doctor.

a Make sure that the power is turned on.

The LCD shows:

b Open the ink cartridge cover a.

c Remove the green protective part a.

d Unpack the ink cartridge.

e Turn the green knob on the protective yellow

cap clockwise until it clicks to release the

vacuum seal, then remove the cap a.

f Take care to match the colour of the lever a

with the cartridge colour b, as shown in the

diagram below.

g Install each ink cartridge in the direction of the

arrow on the label.

Note

Do not throw away the green protective part.

You will need it if you transport the machine.

No Cartridge

Install Ink

Black

Cyan

Yellow

Magenta

Gently push the ink cartridge until it clicks. After

all the ink cartridges are installed close the ink

cartridge cover.

Check the print quality

a When the preparation process has finished, the

LCD shows this message

Press Colour Start.

b Check the quality of the four colour blocks a

on the sheet. (black/yellow/cyan/magenta)

c If all lines are clear and visible, press Yes to

finish the quality check.

If you can see missing short lines, press No and

go to d.

d The LCD asks you if the print quality is OK for

black and colour. Press Yes or No.

After pressing Yes or No for both black and

colour, the LCD shows:

e Press Colour Start, the machine will then start

cleaning the colours.

f After cleaning is finished, press Colour Start.

The machine starts printing the Print Quality

Check Sheet again. Go back to b.

Note

The machine will prepare the ink tube system for

printing. This process will take approximately four

minutes. Do not turn off the machine.

Set Paper and Press Start

Poor

Black OK?

Yes No

Start Cleaning?

Press Start

Choose a Receive Mode

There are three possible receive modes: Fax Only,

Fax/Tel and Manual.

a Press MENU.

b Press a or b to display Initial Setup.

c Press Initial Setup.

d Press Receive Mode.

e Press Fax Only, Fax/Tel or Manual.

f Press Stop/Exit.

You control the

telephone line and must

answer every call

yourself.

Manual

Your machine

automatically answers

every call as a fax.

Fax Only

Your machine controls

the line and

automatically answers

every call. If the call is

not a fax, the telephone

will ring for you to pick

up the call.

Fax/Tel

Your external telephone

answering device (TAD)

automatically answers

every call. Voice

messages are stored

on the external TAD.

If you set Fax Detect

to On, the Fax

messages are printed.

Manual

Yes

Are you using the built-in

TAD?

See Digital TAD in

Chapter 9 of the

User's Guide.

Do you want to use the telephone features of your

machine (if available) or an external telephone or

external telephone answering device connected on the

same line as the machine?

Are you using the voice message

function of an external telephone

answering device?

Do you want the machine to

answer fax and telephone calls

automatically?

Yes

For details, see Using receive modes in

Chapter 6 of the User's Guide.

Set up the TAD

You must record an outgoing message in order to use

the TAD mode.

a Record the TAD outgoing message

(TAD Message).

b Activate TAD mode.

Press . The button will light when the mode

is active.

Set the LCD contrast

(If needed)

If you are having difficulty reading the LCD, try

changing the contrast setting.

a Press MENU.

b Press a or b to display General Setup.

c Press General Setup.

d Press a or b to display LCD Settings.

e Press LCD Settings.

f Press LCD Contrast.

g Press Light, Med or Dark.

h Press Stop/Exit.

Set the date and time

The machine displays the date and time, and if you

set up the station ID, it will add it to each fax you send.

a Press MENU.

b Press a or b to display Initial Setup.

c Press Initial Setup.

d Press Date&Time.

e Enter the last two digits of the year on the

Touchscreen, and then press OK.

(e.g. Enter 0 8 for 2008.)

f Repeat for Month and Day, and Hours and

Minutes in 24-hour format.

g Press Stop/Exit.

See Outgoing message (OGM) in Chapter 9

of the User’s Guide.

If the TAD Mode is on, it overrides your

Receive Mode setting. The built-in digital

TAD answers voice calls. If the call is a fax,

you can receive a fax automatically. For

details, see Digital TAD in Chapter 9 of the

User’s Guide.

Note

You can also adjust the angle of the display by

lifting it.

Year:2008

Year :20 08

Date&Time

Da te& Time

Enter personal

information (station ID)

You should store your name and fax number to be

printed on all fax pages that you send.

a Press MENU.

b Press a or b to display Initial Setup.

c Press Initial Setup.

d Press Station ID.

e Enter your fax number (up to 20 digits) on the

Touchscreen, and then press OK. To enter

numbers or special letters, press

repeatedly until the character you want to enter

appears, then press the character you want to

use. For example, to enter the UK dialling code

“+44”, press until + appears then enter +.

Press until numbers appear then press 4,

4 and the rest of your number.

f Enter your name (up to 20 characters) using

the Touchscreen, and then press OK.

g Press Stop/Exit.

Set tone or pulse dialling

mode

Your machine comes set for Tone dialling service. If

you have Pulse dialling service (rotary), you need to

change the dialling mode.

a Press MENU.

b Press a or b to display Initial Setup.

c Press Initial Setup.

d Press a or b to display Tone/Pulse.

e Press Tone/Pulse.

f Press Pulse (or Tone).

g Press Stop/Exit.

Set the telephone line

type

If you are connecting the machine to a line that

features PBX or ISDN to send and receive faxes, it is

necessary to change the telephone line type

accordingly by completing the following steps.

a Press MENU.

b Press a or b to display Initial Setup.

c Press Initial Setup.

d Press a or b to display Phone Line Set.

e Press Phone Line Set.

f Press Normal, PBX or ISDN.

g Press Stop/Exit.

PBX and TRANSFER

The machine is initially set to Normal, which lets the

machine connect to a standard PSTN (Public

Switched Telephone Network) line. However, many

offices use a central telephone system or Private

Branch Exchange (PBX). Your machine can be

connected to most types of PBX. The machine’s

recall feature supports timed break recall only (TBR).

TBR will work with most PBX systems allowing you to

gain access to an outside line, or transfer calls to

another extension. The feature works when the R key

is pressed.

Note

• If you need to enter a character that is on the

same button as the last character, press c to

move the cursor to the right.

• If you entered a letter incorrectly and want to

change it, press d or c to move the cursor to the

incorrect character, press .

Note

If you make a mistake and want to start again,

press Stop/Exit and go back to a.

For details, see Entering Text in Appendix C

of the User's Guide.

For MFC-790CW:

Now go to

Go to page 13.

For MFC-990CW:

Now go to

To set up the cordless handset, go to Set up

the cordless handset (MFC-990CW only)

on page 11.

To install your machine before you set up the

cordless handset, go to page 13.

Set up the cordless handset (MFC-990CW only)

Install the battery

a Insert the connector a of the battery b in the

direction shown below.

b Place the battery in the position shown.

c Install the battery cover by sliding it onto the

back of the handset.

d Charge the battery by leaving the cordless

handset in the cradle for at least 12 hours

before you use it.

You can continue to set up the handset during

this time.

Charge the battery

a Place the cordless handset on the cradle with

the dial pad facing forward.

Set your country on the

cordless handset

The first time you install the battery, you must set your

country so that the cordless handset works correctly

on local telecommunication lines.

a The LCD shows:

Set Country

Press OK Key

b Press Menu/OK.

c Press a or b to choose your country.

Press Menu/OK.

d Press 1 to confirm.

Note

Be careful that you do not catch the battery

connector cord.

Note

• After battery replacement of the cordless

handset, you should set the date and time.

(See Date and Time in the DECT™ Handset

BCL-D70 User’s Guide.)

• If your battery charge level is getting low, you

should charge the battery. You can see the

battery charge level indicator at the bottom

right of the LCD.

Note

The LCD of the handset will display

“Searching for Base Unit” or

“Base Unit not detected” until the initial

setup of the machine is complete.

Choose a location

 Choose a location where the temperature remains

between 10° C and 35° C.

 Do not put the cordless handset near heaters, air

conditioners, water or chemicals.

 Do not expose the cordless handset to direct

sunlight, excessive heat, moisture, or dust.

 Do not use the cordless handset near electro-

medical equipment.

 We recommend at least 3 m between the machine

(base unit) or cordless handset and possible

sources of radio interference.

Position the antenna on

the base unit

a Move the antenna to the up position as shown

below.

Note

Avoid using in an area where it is difficult for radio

waves to penetrate such as in a reinforced

concrete building, near metal furniture or doors.

For more information about your cordless

handset, please see the DECT™ Handset

BCL-D70 User’s Guide.

3 m3 m

Macintosh

USB

For USB Interface Users (For Mac OS

X 10.2.4 or greater)

Before you install

a Make sure your machine is connected to the

power and your Macintosh

is ON. You must

be logged on with Administrator rights.

Connect the USB cable

a Using both hands, use the plastic tabs on both

sides of the machine to lift the scanner cover

until it locks securely into the open position.

b Connect the USB cable to the USB socket

marked with a symbol. You will find the

USB socket inside the machine on the right as

shown below.

c Carefully guide the USB cable through the

trench as shown below, following the trench

around and toward the back of the machine.

Then connect the cable to your Macintosh

d Lift the scanner cover to release the lock a.

Gently push the scanner cover support

down b and close the scanner cover c.

Important

• For Mac OS

X 10.2.0 to 10.2.3 users,

upgrade to Mac OS

X 10.2.4 or greater. (For

the latest information for Mac OS

X, visit

http://solutions.brother.com/

)

• Make sure there are no memory cards or a

USB Flash memory drive inserted.

Important

• DO NOT connect the machine to a USB port

on a keyboard or a non-powered USB hub.

• Connect the machine directly to your

Macintosh

Important

Make sure that the cable does not restrict the

cover from closing, or an error may occur.

LAN USB

Windows

Wireless Network

Windows

Macintosh

Wireless Network

i The installation of the Brother drivers will

automatically start. The installation screens

appear one after another.

j When the On-Line Registration screen is

displayed, make your selection and follow the

on-screen instructions.

Note

• If the machine is configured for your network,

choose the machine from the list, and then click

Next.

This window will not appear if there is only one

machine connected on the network, it will be

chosen automatically.

If your machine shows APIPA in the IP

Address field, click Configure IP Address

and enter an IP address for your machine that

is suitable for your network.

• If your wireless settings fail, an error message

will appear during the installation of MFL-Pro

Suite and the installation will be terminated. If

you encounter this failure, go to step 21 on

page 30 and setup the wireless connection

again.

• If you are using WEP and the LCD displayed

‘Connected’ but your machine is not found,

make sure you entered the WEP key correctly.

The WEP key is case sensitive.

• If the machine is not yet configured for use on

your network, the following screen appears.

Click OK.

The Configure IP Address window will

appear. Enter an IP address for your machine

that is suitable for your network by following the

on-screen instructions.

Important

DO NOT cancel any of the screens during the

installation. It may take a few seconds for all

screens to appear.

Note

For Windows Vista

, when this screen appears,

click the check box and click Install to complete

the installation correctly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother MFC-990CW in the language / languages: English as an attachment in your email.

The manual is 4,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother MFC-990CW

Brother MFC-990CW User Manual - English - 226 pages

Brother MFC-990CW Installation Guide - German - 47 pages

Brother MFC-990CW User Manual - German - 234 pages

Brother MFC-990CW Installation Guide - Dutch - 47 pages

Brother MFC-990CW User Manual - Dutch - 235 pages

Brother MFC-990CW Installation Guide - French - 47 pages

Brother MFC-990CW User Manual - French - 235 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother MFC-990CW Manual

Product: