718891
8
Zoom out
Zoom in
Previous page
1/76
Next page
6
Powering the machine
Turning on the machine
1. Insert the three-pin plug into the socket on the
bottom right side of the machine. Insert the
power supply plug into a power outlet.
2. Turn the main power and light switch <A> to "I"
mark (to "O" mark to turn off).
<A>
Operation
When the foot controller is pressed lightly, the
machine runs at a low speed. As the foot controller
is pressed further, the machine will increase
speed. When the foot controller is released, the
machine stops.
NOTE (For U.S.A. only):
Foot controller: Model KD-1902
This foot controller can be used on the machine
with product code 884-B02 and 884-B03.
* The product code is shown on the machine rating
plate.
Turning direction of hand wheel
The hand wheel <A> turns in a counterclockwise
direction (direction of arrow). This is the same
direction as an ordinary home sewing machine.
The needles move to their highest positions by
turning the hand wheel so that the mark <B>
on the hand wheel is aligned to the line on the
machine.
<A>
<B>
Opening/ Closing front cover
It is necessary to open the front cover when
threading this machine. Slide it to the right
1
and
open
2
, or close it and slide it to the left.
CAUTION
For your safety, make sure that the front cover is
closed when operating the machine.
Always turn off the machine before opening the
front cover.
1
2
Attaching/ Removing presser foot
1. Turn off the main power and light switch or
disconnect the electric supply plug.
2. Raise the presser foot lever.
1
3. Turn the hand wheel
2
so that the mark on
the hand wheel is aligned to the line on the
machine. (See CHAPTER1 "Turning direction
of hand wheel".)
4.
Push the button on the presser foot holder and
the standard presser foot will be released.
3 4
5. Raise the presser foot farther by pushing the
presser foot lever upward. Then remove the
presser foot and store it in a safe location.
6. Again, raise the presser foot farther by pushing
the presser foot lever upward. Then place the
presser foot just under the presser foot holder
<A> so that the groove in the bottom of the
presser foot holder <B> is aligned and catches
the bar on the top of the foot <C>. Then lower
the presser foot lever to attatch the foot,
pushing the button on the presser foot.
<A>
<C>
<B>
1
1
2
3
2
4
4
8


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-m343d

Reset search

  • Como regular para hacer dobladillo en tela de gasa o organza Submitted on 9-6-2023 at 18:35

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother M343D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother M343D in the language / languages: English, Spanish as an attachment in your email.

The manual is 4,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother M343D

Brother M343D User Manual - German - 76 pages

Brother M343D User Manual - Dutch, French - 76 pages

Brother M343D User Manual - Italian - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info