Manual Brother LS1317 (page 46 of 81) (English, French, Portuguese, Spanish)

555743

Zoom out

Zoom in

1/81

CONTENTS INDEXMAINTENANCE

KNOWING YOUR

SEWING MACHINE

STRAIGHT AND

ZIGZAG STITCHING

BUILT-IN STITCHES

BUTTONHOLE AND

BUTTON SEWING

USING ATTACHMENTS

AND APPLICATIONS

Buttonhole Sewing

STITCH LENGTH Set between 0 and 1 (F) for the Satin Stitch.

STITCH WIDTH See the instructions below.

NEEDLE POSITION R (right position)

PRESSER FOOT Zigzag

NEEDLE Single

Making a buttonhole

NOTE:

1. It is recommended to practice making a buttonhole on a scrap piece of

fabric before attempting it on your project.

2. Using tailor’s chalk to mark the position and length of the buttonhole on

the fabric is also recommended.

Step A: Bar Tack

1. Set the stitch length between 0 and 1 (F), stitch width to 5 and the needle

position to R.

2. Lower the presser foot over the top right corner of the buttonhole mark and

sew 3-6 stitches.

3. Stop the machine when the needle is in the fabric on the right side of the

stitch (position A). (Turn the balance wheel counterclockwise if neces-

sary.)

Step B: Right Row

1. Set the stitch width to 2.

2. Sew the predetermined length of the buttonhole to the other end.

3. Stop the machine when the needle is in the fabric on the right side of the

stitch (position B). (Turn the balance wheel counterclockwise if necessary.)

Step C: Final Bar Tack

1. Set the stitch width to 5.

2. Sew 3-6 stitches.

3. Stop the machine when the needle is in the fabric on the left side of the

stitch (position C). (Turn the balance wheel conterclockwise if necessary.)

Step D: Left Row

1. Lift the presser foot.

2. Turn the fabric 180 degrees using the needle as an axis and set the stitch

width to 0. This will move the fabric slightly. Lower the presser foot.

3. Turn the balance wheel toward you (counterclockwise) to sew one stitch.

This moves the needle from the left to the right.

4. Set the stitch width to 2.

5. Sew until the needle reaches the other bar tack. Stop the machine with the

needle in the fabric on the right of the stitches (position D).

Securing the stitching and cutting the buttonhole

1. To secure the stitching, turn the fabric 90 degrees counterclockwise,

set the stitch width to 0, the stitch length to 1 and sew 5-6 Straight

Stitches as shown in fig. E.

2. Remove the fabric from the machine.

3. It is recommended that pins be placed across both bartack ends of

the buttonhole as protection against cutting the stitches.

4. Cut an opening in the middle of the buttonhole with a seam ripper

tool. Be careful not to cut through any stitches.

Coudre une boutonnière

Longueur de point

Réglée entre 0 et 1 (F) pour le point bourdon.

Largeur de point Voir les instructions ci-dessous.

Position de l’aiguille R (à droite)

Pied-de-biche Zigzag

Aiguille Simple

Faire une boutonnière

REMARQUE :

1. Il est conseillé de s’entraîner au préalable sur une chute de tissu

avant d’essayer de coudre la boutonnière sur le tissu souhaité.

2. Il est également conseillé de marquer sur le tissu la position et la

longueur de la boutonnière à l’aide d’une craie de tailleur.

Etape A : Barres d’arrêt

1. Régler la longueur de point entre 0 et 1 (F), la largeur de point sur

5 et la position de l’aiguille sur R.

2. Abaisser le pied-de-biche sur le coin en haut et à droite de la bou-

tonnière et faire 3-6 points.

3. Arrêter la machine lorsque l’aiguille se trouve dans le tissu et à

droite du point (emplacement A) (Tourner le volant à main dans le

sens contraire des aiguilles d’une montre si nécessaire).

Etape B: côté droit

1. Régler la largeur de point sur 2.

Coudre la longueur préalablement choisie de la boutonnière jusqu’au bout.

3. Arrêter la machine lorsque l’aiguille se trouve dans le tissu et à

droite du point (emplacement B). (Tourner le volant à main dans le

sens contraire des aiguilles d’une montre si nécessaire).

Etape C: dernière barre d’arrêt

1. Régler la largeur de point sur 5.

2. Faire 3-6 points.

3. Arrêter la machine lorsque l’aiguille se trouve dans le tissu et à

gauche du point (emplacement C). (Tourner le volant à main dans

le sens contraire des aiguilles d’une montre si nécessaire).

Etape D: côté gauche

1. Relever le pied-de-biche.

Faire pivoter le tissu de 180 degrés autour de l’aiguille et régler la largeur

de point sur 0. Le tissu bougera légèrement. Abaisser le pied-de-biche.

3. Tourner le volant vers soi (dans le sens contraire des aiguilles d’une

montre). L’aiguille se déplacera de gauche à droite.

4. Régler la largeur de point sur 2.

5. Coudre jusqu’à ce que l’aiguille atteigne l’autre barre d’arrêt. Arrê-

ter la machine; l’aiguille doit se trouver dans le tissu à droite des

points (emplacement D).

Consolider les points et couper la boutonnière

Pour consolider les points, faire pivoter le tissu de 90 degrés dans le sens

contraire des aiguilles d’une montre, régler la largeur de point sur 0, la

longueur de pointe sur 1 et faire 5-6 points droits comme l’indique la fig. E.

2. Retirer le tissu de la machine.

3. Il est conseillé de placer des épingles à travers la fin des barres

d’arrêt de la boutonnière pour éviter de couper les points.

4. Faire une ouverture au milieu de la boutonnière à l’aide d’un dé-

coud-vite. Veiller à ne pas couper les points.

(E)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS1317 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother LS1317 Manual

Product: