555741

Brother LS1217 Manual

65
Zoom out
Zoom in
Previous page
1/81
Next page
55
CONTENTS INDEXMAINTENANCE
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
Cleaning
Removing the Shuttle Hook
1. Raise the needle to its highest position.
2. Open the shuttle cover on the front of the free arm.
3. Take out the bobbin case by opening its latch and pulling it out
from the shuttle race.
4. Slide the latch levers out from the retaining ring and remove the
retaining ring. See fig. A.
1 Retaining ring
2 Latch lever
5. Remove the hook by grasping the center post of the hook and pull-
ing it out as shown in fig. B.
3 Hook
4 Hook center post
NOTE:
When the needle is lowered, the shuttle hook cannot be removed.
Cleaning the Shuttle Race
1. Remove any accumulated lint and thread with a brush from the
retaining ring, hook, driver and race body .
5 Driver
6 Race body
2. A cloth dampened with machine oil should be used to wipe the
shuttle race clean of lint.
3. Clean the lint from the shuttle hook using a cloth dampened with
machine oil.
4. Reassemble the hook with the notch at the top and push the latch
levers back to their positions to hold the retaining ring in place.
NOTE:
If the needle has moved, you will need to return it to its highest posi-
tion before reinstalling the hook. The hook will not go back into place
unless the needle and take-up lever are in their highest positions.
Cleaning the Feed Dogs
1. Remove the needle plate using a coin or screwdriver to remove the
screws.
2. Clean the lint from the upper part of the feed dogs and shuttle race
body with a brush.
A
1
2
B
C
6
1
5
3
1
4
Nettoyage
Retirer le crochet de la navette
1. Remonter complètement l’aiguille.
2. Ouvrir le couvercle de la navette situé à l’avant du bras libre.
3. Tirer sur le loquet puis sortir le boîtier de la canette hors de la
coursière.
4. Faire glisser les leviers du loquet de la bague de retenue puis retirer
celle-ci. Voir fig.A.
1
Bague de retenue
2
Levier du loquet
5. Retirer le crochet en saisissant son axe central et en le tirant comme
l’indique la fig. B.
3
Crochet
4
Axe central du crochet
REMARQUE:
Il est impossible de retirer le crochet de la navette lorsque l’aiguille est
abaissée.
Nettoyage de la coursière de la navette
1. Retirer toute bourre et fil à l’aide d’une brosse de la bague de rete-
nue, du crochet, de l’entraînement et de la coursière.
5
Entraînement
6
Coursière
2. Utiliser un chiffon imbibé d’huile de machine pour débarrasser la
coursière de la navette de toute bourre.
3. Utiliser un chiffon imbibé d’huile de machine pour débarrasser le
crochet de la navette de toute bourre.
4. Réinstaller le crochet, avec l’encoche vers le haut, et repousser les
leviers de loquets en place de façon à ce qu’ils maintiennent la
bague de retenue en place.
REMARQUE :
Si l’aiguille a bougé, la remonter complètement avant de remettre le
crochet en place. Le crochet ne se remettra pas en place si l’aiguille et
le levier releveur ne sont pas entièrement remontés.
Nettoyage des griffes d’entraînement
1. Retirer la plaque à aiguille en utilisant une pièce de monnaie ou un
tournevis pour enlever les vis.
2. Débarrasser la partie supérieure des griffes d’entraînement ainsi
que la coursière de la navette de toute bourre à l’aide d’une brosse.
… 65 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS1217 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS1217 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info