555741

Brother LS1217 Manual

61
Zoom out
Zoom in
Previous page
1/81
Next page
51
CONTENTS INDEXMAINTENANCE
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
Monogramming and Embroidering
STITCH LENGTH Set at any position.
STITCH WIDTH 0-5
NEEDLE POSITION M
PRESSER FOOT None
NEEDLE Single
OTHERS Darning plate
Preparing for monogramming and embroidering
1. Place the darning plate on the needle plate.
2. Draw the lettering (for monogramming) or design (for embroider-
ing) on the surface of the fabric with delible ink or tailor’s chalk.
3. Stretch the fabric in an embroidery hoop as firmly as possible with
the underside of the fabric on the bottom of the inside hoop.
4. Place the work under the needle and lower the presser bar with the
foot removed.
5. Pull the lower thread up through the work at the starting position
by turning the balance wheel and make a few stitches to hold the
end of the thread.
6. Grip the hoop with the thumb and forefingers of both hands while
pressing the fabric with the middle and third fingers and supporting
the outside of the hoop with your smaller fingers.
Monogramming
1. Sew moving the hoop slowly along the lettering at a constant speed.
2. Secure with a few straight stitches at the end of the last letter.
Embroidering
1. Stitch the outline of the design by moving the embroidery hoop.
2. Fill in the design alternately from the outline of the design to the
inside and from the inside to the edge of the outline until the de-
sign is completely filled in. Keep the stitching close together.
NOTE:
A long stitch is made by moving the embroidery hoop rapidly and a
short stitch is made by moving it slowly.
3. Secure with a few straight stitches at the end of the design.
CAUTION:
Keep fingers away from moving parts, especially needles.
Monogrammes et broderies
LONGUEUR DE POINT N’importe quel réglage
LARGEUR DE POINT 0-5
POSITION DE L’AIGUILLE M
PIED-DE-BICHE Aucun
AIGUILLE Simple
AUTRES Plaque à repriser
Préparation avant de faire des monogrammes et broderies
1. Placer la plaque à repriser sur la plaque à aiguille.
2. Tracer les lettres (du monogramme) ou le motif (de la broderie) sur
le tissu avec de l’encre délébile ou de la craie de tailleur.
3. Tendre le plus possible le tissu sur un tambour de broderie, l’en-
vers du tissu situé au fond du tambour.
4. Placer l’ouvrage sous l’aiguille et abaisser la barre, le pied-de-bi-
che ayant été retiré.
5. Tirer le fil inférieur vers le haut à travers l’ouvrage à la position de
départ en tournant le volant et faire quelques points de maintien.
6. Saisir le tambour avec le pouce et les index des deux mains tout en
appuyant sur le tissu avec les majeusr et les annulaires et en tenant
l’extérieur du tambour avec les auriculaires.
Monogrammes
1. Coudre, en déplaçant lentement le tambour, le long des lettres tout
en maintenant une vitesse constante.
2. Faire quelques points droits de renfort à la fin de la dernière lettre.
Broderies
1. Piquer la ligne extérieure du motif en déplaçant le tambour.
2. Coudre l’intérieur du motif en allant de l’extérieur vers l’intérieur
puis de l’intérieur vers l’extérieur en alternance jusqu’à ce que le
motif soit terminé. Les points doivent être rapprochés.
REMARQUE:
Pour obtenir un long point, déplacer le tambour rapidement, pour un
point court, le déplacer lentement.
3. Faire quelques points de renfort lorsque le motif est terminé.
PRECAUTION:
Tenir les doigts à l’écart de tout élément mobile, en particulier les
aiguilles.
… 61 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS1217 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS1217 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info