631286

Brother LS-3125 Manual

33
Zoom out
Zoom in
Previous page
1/68
Next page
24
Straight Stitching
The Straight Stitch (6-10 or 11) is used for top stitching and
sewing lightweight fabrics.
Starting Sewing (fig. A)
1. Set the pattern selection dial to the appropriate Straight Stitch
(6-10 or 11) with the desired length.
2. Raise the needle to its highest position and lift the presser foot lifter.
3. Pull up the bobbin thread by turning the balance wheel
toward you (counterclockwise) and place both the upper and
lower threads toward the back behind the presser foot.
4. Place the fabric under the presser foot and position the needle
1 cm (3/8") from the edge of the fabric.
5. Lower the presser foot.
6. To backtack, press the reverse sewing lever down as far as
possible and lightly touch the foot controller. Sew 5 to 10
stitches in the reverse direction.
7. Release the reverse sewing lever and start sewing in the
forward direction by applying pressure to the foot controller.
NOTE:
The backtack or reverse sewing is used for locking the end of
seams and reinforcing stitches.
Changing Sewing Direction (fig. B)
1. Stop the machine at the point where you wish to change directions with the
needle still in the fabric. If the needle ends in the up position, turn the balance
wheel toward you (counterclockwise) until the needle enters the fabric.
2. Raise the presser foot and turn the fabric to line up its new
direction using the needle as a pivot point.
3. Lower the presser foot and start sewing in the new direction.
NOTE:
For twin needle sewing, raise the needle when changing the
sewing direction.
Finishing Sewing (fig. C)
Reverse stitching is used to lock the threads at the end of the
seam or wherever reinforcement is needed.
1. Stitch to the end of the seam and stop.
2. Press the reverse sewing lever down and lightly touch the foot
controller to stitch backwards for 1 cm (3/8") from the end of
the fabric over the top of the existing stitch.
Removing the Fabric From the Machine (fig. D)
1. Stop the machine.
2.
Turn the balance wheel toward you (counterclockwise) to bring
the needle and thread take-up lever to their highest position.
3. Lift the presser foot and pull the fabric out gently to the left side.
4. Cut both threads using the thread cutter located on the back of
the presser foot bar.
a Thread cutter
5. To prepare the machine for the next seam, pull about 10 cm (4") of
both threads and place them toward the back of the machine. The
upper thread should pass between the toes of the presser foot.
Pattern
6-10 (Center needle position)
11 (Left needle position)
Point droit
Le point droit (modèle 6-10 ou 11) sert pour la “haute couture” et
pour coudre sur des tissus légers.
Pour commencer à coudre (fig. A)
1. Régler le sélecteur de modèle sur le point droit approprié (6-
10 ou 11), avec la longueur souhaitée.
2. Remonter complètement l’aiguille et relever le levier du pied-de-biche.
3. Remonter le fil inférieur en tournant le volant vers soi (dans le
sens opposé aux aiguilles d’une montre) et tirer les deux fils,
inférieur et supérieur, vers l’arrière du pied-de-biche.
4. Placer le tissu sous le pied-de-biche et mettre l’aiguille à 1 cm
du bord du tissu.
5. Abaisser le pied-de-biche.
6. Pour arrêter la couture, abaisser complètement le levier de
couture en marche arrière et appuyer légèrement sur la
pédale. Faire 5 à 10 points en marche arrière.
7. Relâcher le bouton de couture en marche arrière et
commencer à coudre en avant en appuyant sur la pédale.
REMARQUE :
La couture en marche arrière sert à terminer les coutures et à
consolider les points.
Pour modifier le sens de la couture (fig. B)
1. Arrêter la machine à l’endroit souhaité pour le changement de
direction, en laissant l’aiguille piquée dans le tissu. Si l’aiguille est en
position relevée, tourner le volant vers soi (dans le sens opposé aux
aiguilles d’une montre) jusqu’à ce que l’aiguille pénètre dans le tissu.
2. Relever le pied-de-biche et faire pivoter le tissu autour de l’axe
formé par l’aiguille, pour l’orienter dans la nouvelle direction.
3. Abaisser le pied-de-biche et commencer à coudre dans le nouveau sens.
REMARQUE:
Pour la couture avec une aiguille jumelée, relever l’aiguille pour
changer de direction de couture.
Pour terminer la couture (fig. C)
Utiliser la couture en marche arrière pour faire un noeud à la fin
d’une couture ou consolider des points.
1. Piquer jusqu’au bout de la couture puis arrêter la machine.
2. Abaisser le levier de couture en marche arrière et appuyer
légèrement sur la pédale pour coudre sur 1 cm en arrière à
partir du bord du tissu et recouvrir les points existants.
Pour retirer le tissu de la machine (fig. D)
1. Arrêter la machine.
2. Tourner le volant vers soi (dans le sens contraire des aiguilles d’une
montre) pour remonter complètement l’aiguille et le levier releveur de fil.
3. Relever le pied-de-biche et dégager doucement le tissu vers la gauche.
4. Couper les deux fils à l’aide du coupe-fils situé derrière la
barre du pied-de-biche.
a Coupe-fils
5. Afin de préparer la machine pour la couture suivante, tirer environ
10 cm des deux fils et les placer vers l’arrière de la machine. Le fil
supérieur doit passer entre les branches du pied-de-biche.
Modèle
6-10 (Aiguille au centre)
11 (Aiguille à gauche)
Puntada recta
La puntada recta (No 6-10 ó 11) se usa para costuras de remate y
para coser materiales ligeros.
Número de puntada
6-10 (Aguja en el centro)
11 (Aguja a la izquierda)
Прямая строчка
Прямая строчка (6-10 или 11) используется для отделки
деталей одежды и шитья лёгких тканей.
Положение ручки выбора вида строчки
6-10 (Центральное положение иглы)
11 (Левое положение иглы)
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS-3125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS-3125 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info