458318

Brother LS-2129 Manual

29
Zoom out
Zoom in
Previous page
1/67
Next page
21
2
1
2
1
NOTE:
The bobbin thread tension has already been adjusted at the
factory for general use. For most sewing applications, no
adjustment is needed.
When sewing with thin thread on thin fabrics, the thread tension
may not be adjusted adequately with the upper tension control
dial. Therefore, the thread tension must be adjusted according to
the procedure described below.
C Bobbin tension is too loose.
Locks appear on the surface of the fabric.
Decrease the thread tension by turning the dial to a lower
number. If the result is still not satisfactory, then adjust the
bobbin thread tension as explained in C-1
C-1 Bobbin
Increase the tension in the bobbin by turning the screw with
a small screwdriver in a clockwise direction. However, do
not turn the screw more than one full turn.
Remember to return the screw to its original setting before
starting your next project.
D Correct tension
Correct tension is important since too much or too little tension
will weaken your seams or cause puckers in your fabric.
a Reverse
b Surface
REMARQUE:
La tension du fil inférieur a déjà été réglée d’usine pour une
utilisation normale. Pour la plupart des applications de couture, il
ne sera dès lors pas nécessaire de la régler.
Cependant, lors de la couture avec du fil fin sur des tissus légers,
les réglages de tension du fil effectués à l’aide du disque de
contrôle de la tension supérieure sont insuffisants. Dans ce cas,
régler la tension du fil selon la méthode décrite ci-dessous.
C La tension inférieure est insuffisante.
Formation de boucles à l’endroit du tissu.
Diminuer la tension du fil en mettant le disque sur un chiffre
inférieur. Si le résultat n’est pas encore concluant, régler la
tension du fil de la canette comme expliqué au point C-1.
C-1 Canette
A l’aide d’un petit tournevis, augmenter la tension de la
canette en tournant la vis dans le sens des aiguilles d’une
montre, sans effectuer plus d’un tour complet.
Ne pas oublier de remettre la vis à sa position originale avant
d’entamer un nouvel ouvrage.
D Tension correcte
Il est essentiel de procéder à un réglage correct de la tension du
fil pour avoir des coutures solides sans que le tissu ne fronce.
1 Envers
2 Endroit
NOTA:
La tensión del hilo inferior ya se ha ajustado en fábrica para los usos
comunes. Por lo tanto, para la mayoría de las costuras, no se
requerirá ningún ajuste adicional.
Sin embargo, al coser con hilo delgado en tejidos finos, no se puede
ajustar correctamente la tensión del hilo mediante el disco de control
de la tensión superior. En esos casos, la tensión del hilo ha de ser
ajustada de acuerdo con el proceso descrito a continuación.
C La tensión del hilo inferior es insuficiente.
Aparecen bagas en la superficie del tejido.
Disminuya la tensión del hilo al girar el disco hacia un número
inferior. Si el resultado no le conviene aún, ajuste la tensión del
hilo de la canilla tal como se indica en C-1.
C-1 Canilla
Aumente la tensión en la canilla girando el tornillo, con un pequeño
destornillador, en el sentido de las manecillas de un reloj. Sin
embargo, no conviene dar más de una vuelta completa al tornillo.
No olvide volver a colocar el tornillo en su posición original
antes de empezar otro tipo de costura.
D Tensión correcta
Es importante tener una tensión correcta dado que una tensión
insuficiente o demasiada tirante va a debilitar sus costuras o
fruncir el tejido.
a Revés
b Derecho
NOTA:
A tensão da linha inferior vem regulada de fábrica para trabalhos
normais de costura. Para a maioria das aplicações, não é necessário
qualquer ajuste.
Quando costurar tecidos finos com linha fina, a tensão da linha não
pode ser adequadamente regulada apenas com o disco de regulagem
da tensão da linha superior. É necessário regular a tensão da linha
segundo o processo abaixo descrito.
C A linha inferior está muito frouxa.
Aparecem pontos com laçadas na parte superior (direito) do tecido.
Diminua a tensão da linha girando o disco de regulagem da
tensão da linha superior para um número inferior. Se o resultado
ainda não for satisfatório, ajuste então a tensão da linha da
bobina, da forma abaixo explanado em C-1.
C-1 Bobina
Aumente a tensão da linha na bobina girando o parafuso com
uma pequena chave-de-fendas, para a direita. Todavia, não gire o
parafuso mais de uma volta completa.
Não se esqueça de repor este parafuso na sua posição inicial
antes do seu próximo trabalho.
D Tensão correcta
É importante que a tensão esteja correcta porque se for excessiva
ou insuficiente enfraquecerá as costuras ou provocará a
ocorrência de franzidos no tecido.
a Avesso
b Direito
D
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS-2129 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS-2129 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info