458318

Brother LS-2129 Manual

14
Zoom out
Zoom in
Previous page
1/67
Next page
6
1
1
Inserting the Needle
Turn power switch to “O”.
1. Remove the power supply plug from the electrical outlet.
2. Raise the needle bar to its highest position.
3. Lower the presser foot.
4. If a needle is already installed, remove the needle by
loosening the needle clamp with a coin and pulling the
needle down.
5. With the flat side toward the back, insert the new needle as far
as possible up against the needle stopper.
6. Tighten the needle clamp.
a Coin
Checking the Needle
1. The sewing needle must always be straight and sharp for
smooth sewing.
2. To check if the needle is bent, place the flat side of the needle
down as shown in the illustration.
3. Replace the needle if it is bent or dull.
Pour mettre l’aiguille en place
Mettre l’interrupteur d’alimentation sur “O”.
1. Retirer la fiche de la prise de courant.
2. Remonter complètement l’aiguille.
3. Abaisser le pied-de-biche.
4. Retirer l’aiguille éventuellement présente en dévissant la fixation
avec une pièce de monnaie et en tirant l’aiguille vers le bas.
5. Introduire une autre aiguille côté plat vers l’arrière, en
l’enfonçant au maximum jusqu’à ce qu’elle vienne heurter le
butoir.
6. Resserrer la fixation.
a Pièce de monnaie
Vérification de l’aiguille
1. L’aiguille doit toujours être droite et pointue pour piquer
correctement.
2. Pour vérifier si l’aiguille n’est pas tordue, placer le côté plat de
l’aiguille vers le bas, comme le montre l’illustration.
3. Remplacer l’aiguille si elle est tordue ou usée.
Inserción de la aguja
Coloque el interruptor principal en “O”.
1. Retire el enchufe de alimentación de la toma de corriente.
2. Levante la barra de la aguja a su posición más alta.
3. Baje el prensatelas.
4. En caso de que ya esté una aguja instalada, retírela aflojando el
tornillo con una moneda y tirándola hacia abajo.
5. Introduzca otra aguja, con la parte redonda cara a usted. Hay que
meterla lo más adentro posible hasta que toque arriba con el
pasador.
6. Vuelva a apretar el tornillo de la aguja.
a Moneda
Comprobación de la aguja
1. La aguja siempre ha de estar bien recta y afilada para un perfecto
cosido.
2. Para comprobar que la aguja no está doblada, coloque la parte
plana de la aguja hacia abajo como se muestra en el dibujo.
3. Cambie la aguja si está doblada o gastada.
Colocação da agulha
Gire o interruptor de força até “O”.
1. Desligue o plugue da tomada.
2. Levante a agulha até sua posição mais alta.
3. Abaixe o pé calcador
4. Retire a agulha (caso haja uma instalada) girando o parafuso
prendedor com uma moeda.
5. Insira a outra agulha com lado chato voltado para trás e o lado corn
a ranhura voltado para você. Empurre-a até o encosto.
6. Aperte firmemente o parafuso prendedor da agulha.
a Moeda
Verificação da agulha
1. Para uma costura ideal, a agulha deve ser perfeitamente reta e
pontiaguda.
2. Para verificar se a agulha está empenada apoie o seu lado plano
sobre uma superfície reta.
3. Troque-a se você perceber que ela está empenada ou defeituosa.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS-2129 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS-2129 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info