1897
13
Zoom out
Zoom in
Previous page
1/66
Next page
6
Nadel einsetzen
Netzschalter auf O stellen.
1. Ziehen Sie den Netzstecker aus der Steckdose.
2. Drehen Sie die Nadel mit dem Handrad in die höchste Position.
3. Senken Sie den Nähfuß ab.
4. Falls bereits eine Nadel eingesetzt ist, entfernen Sie sie, indem
Sie die Nadelschraube mit einer Münze lösen und die Nadel
nach unten herausziehen.
5. Setzen Sie eine neue Nadel mit der flachen Seite nach hinten
ein. Schieben Sie die Nadel so weit wie möglich nach oben bis
zum Anschlag.
6. Ziehen Sie die Nadelschraube fest.
1 Münze
Pour mettre laiguille en place
Mettre linterrupteur dalimentation sur O.
1. Retirer la fiche de la prise de courant.
2. Remonter complètement laiguille.
3. Abaisser le pied-de-biche.
4. Retirer laiguille éventuellement présente en dévissant la fixa-
tion avec une pièce de monnaie et en tirant laiguille vers le
bas.
5. Introduire une autre aiguille côté plat vers larrière, en lenfon-
çant au maximum jusqu’à ce quelle vienne heurter le butoir.
6. Resserrer la fixation.
1
Pièce de monnaie
De naald erin doen
Aan/uit-schakelaar op O zetten.
1. Haal de stekker uit het stopcontact.
2. Zet de naaldhouder in de hoogste positie.
3. Laat de persvoet zakken.
4. Als er al een naald inzit, draai de naaldklem dan los met een munt-
stuk en verwijder de naald door het naar beneden te trekken.
5. Schuif de nieuwe naald er met de platte kant naar achteren zo ver
mogelijk in tot het tegen de naaldstopper aankomt.
6. Draai de naaldklem weer vast.
1 Muntstuk
Nadel prüfen
1. Die Nähnadel muß für problemloses Nähen immer gerade und
scharf sein.
2. Um zu prüfen, ob die Nadel verbogen ist, legen Sie die Nadel
mit der flachen Seite nach unten hin, wie in der Abbildung
gezeigt.
3. Ersetzen Sie die Nadel, wenn sie verbogen oder stumpf ist.
1
1
Vérification de laiguille
1. Laiguille doit toujours être droite et pointue pour piquer cor-
rectement.
2. Pour vérifier si laiguille nest pas tordue, placer le côté plat de
laiguille vers le bas, comme le montre lillustration.
3. Remplacer laiguille si elle est tordue ou usée.
De naald controleren
1. Voor het beste resultaat moet de naald altijd recht en scherp zijn.
2. Door de naald zoals in de illustratie met de platte kant op een platte
ondergrond te leggen, kunt u controleren of deze recht is.
3. Indien de naald verbogen of bot is, moet deze worden vervangen.
Montaggio dellago
Posizionare linterruttore di alimentazione su O.
1. Disinserire la spina di alimentazione dalla presa di corrente.
2. Far salire la barra dellago fino alla sua posizione più alta.
3. Abbassare il piedino premistoffa.
4. Se un ago è già montato, allentare il morsetto dellago ruotandolo
con una moneta ed estrarre lago.
5. Inserire il nuovo ago con la parte piatta rivolta allindietro spingen-
dolo più in alto possibile fino al suo arresto.
6. Stringere il morsetto dellago.
1 Moneta
Controllo dellago
1. Per ottenere una cucitura perfetta, lago utilizzato deve essere sem-
pre ben diritto ed appuntito.
2. Per controllare se lago è piegato, appoggiarlo su un piano con la
parte piatta come illustrato dal disegno.
3. Sostituire lago se risulta piegato o spuntato.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS 2125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS 2125 in the language / languages: German, Dutch, French, Italian as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother LS 2125

Brother LS 2125 User Manual - English, French, Portuguese, Spanish - 67 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info