770156
55
Zoom out
Zoom in
Previous page
1/72
Next page
48
TABLE OF
CONTENTS
Chapter
1
Chapter
2
Chapter
3
Chapter
4
Chapter
5
Chapter
6
Chapter
7
Chapter
8
Chapter
9
Chapter
10
Chapter
11
Chapter
12
Chapter
13
Chapter
14
Chapter
15
Chapter
16
Chapter
17
Chapter
18
Chapter
19
(6)Ajuste el largo de las puntadas.
Coloque la palanca de ajuste del largo de las
puntadas en la posición “R” tal como lo muestra
la ilustración. Este ajuste conviene tanto para las
puntadas overlock estrechas como para las de
dobladillo enrollado.
Para realizar puntadas de borde enrollado
Esta función permite meter el borde del tejido en las
puntadas de dobladillo. Para poder realizarlo, con-
viene aumentar la tensión del áncora inferior. Así, se
tira del hilo del áncora superior y el borde del tejido
se dobla alrededor de la uñeta remanente. Después
de implementar las operaciones (1) a (6) indicadas
arriba, se recomienda ajustar la máquina en los
siguientes valores de tensión de hilo:
Tensión del hilo del áncora superior entre 1-4
Tensión del hilo del áncora inferior entre 5-7
Tensión del hilo de la aguja derecha en 4.
La tensión puede variar ligeramente según los teji
dos e hilos utilizados.
Para realizar puntadas overlock estrechas
Esta función decorativa conviene para mejor termi-
nar el borde del tejido. Después de los puntos (1) a
(6) indicados arriba, ajuste las tensiones de los hilos
con vistas a lograr una puntada overlock normal de
tres hilos. Los ajustes de tensión recomendados
son:
Todas las tensiones de los hilos deben estar en 4. La
tensión puede variar dependiendo de los tejidos e
hilos utilizados.
(6)Adjust the stitch length.
Set the stitch length adjustment lever to “R”
position as shown in the illustration. This adjust-
ment is suitable for either Narrow Overlock stitch
or Rolled Edge stitch.
To Do Rolled Edge Stitch
This application rolls the edge of the fabric inside of
the hem stitch. The lowerlooper tension should be
tightened. This pulls the upperlooper thread causing
the edge of the fabric to fold around the remaining
stitch finger. After completing steps (1) through (6)
above, adjust your machine to these recommended
thread tension settings:
Upperlooper thread tension at 1-4
Lowerlooper thread tension at 5-7
Right needle thread tension at 4
Tension may vary slightly according to the fabric and
thread used.
To Do Narrow Overlock Stitch
This is a decorative application used for finishing the
edge of the fabric. After completing steps (1) through
(6) above, adjust the thread tension to achieve a
normal 3-thread overlock stitch.
Recommended thread tension settings are:
All thread tensions should be set at 4
Tension may vary slightly according to the fabric and
thread used.
2
R4
3
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Lock 929D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Lock 929D in the language / languages: Dutch as an attachment in your email.

The manual is 2.68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info