718835
15
Zoom out
Zoom in
Previous page
1/47
Next page
14
1
3
Pass the end of the thread through the hole
on the bobbin from the inside of the bobbin.
4
Put the bobbin onto the bobbin winder
shaft and slide the bobbin winder shaft to
the right. Turn the bobbin clockwise, by
hand, until the projection slides into the
notch of the bobbin.
Make sure to pull out 7 to 10 cm (3-4 inches)
of thread from the hole on the bobbin.
1 Projection
2 Notch
3 7-10 cm (3 – 4 inches)
CAUTION
5
Turn on the machine.
CAUTION
6
While holding the end of the thread,
gently press the foot controller to wind
the thread around the bobbin a few times.
Then stop the machine.
7
Trim the excess thread above the bobbin.
Leave 1 cm (1/2 inch) of thread from the hole
on the bobbin.
1 1 cm (1/2 inch)
CAUTION
8
Press the foot controller to start.
9
When the bobbin seems full and begins
spinning slowly, take your foot off the foot
controller.
0
Cut the thread, slide the bobbin winder
shaft to the left and remove the bobbin.
Note
When the sewing machine is started or the
handwheel is turned after winding the thread
around the bobbin, the machine will make a
clicking sound; this is not a malfunction.
The needle bar does not move when you
slide the bobbin winder shaft to the right.
CAUTION
Pull the thread taut and hold the end of
the thread straight up. If the thread is too
short, not pulled taut or held at an angle,
injuries may occur when the thread is
wound around the bobbin.
Do not turn on the machine while pressing
down the foot controller. The machine
may start unexpectedly and cause
personal injury or damage to the machine.
3
1
2
Make sure you follow the instructions
carefully. If you do not cut the excess thread
completely before winding the bobbin, when
the thread runs low it may tangle around the
bobbin and cause the needle to break.
Not winding the bobbin properly may
cause the thread tension to loosen, and
may break the needle.
1 Wound evenly
2 Wound poorly
1
1
2
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother KE14S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother KE14S in the language / languages: English as an attachment in your email.

The manual is 12,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother KE14S

Brother KE14S User Manual - German - 47 pages

Brother KE14S User Manual - Dutch - 47 pages

Brother KE14S User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info