718712
14
Zoom out
Zoom in
Previous page
1/72
Next page
12
KNOWING YOUR SEWING MACHINE
g
Slide the sewing speed controller to the right (to
set the speed to fast). (For models equipped with
the sewing speed controller.)
h
Press the foot controller or press (start/stop
button) (for models equipped with the start/stop
button) to start.
i
When the bobbin seems full and begins spinning
slowly, take your foot off the foot controller or
press (start/stop button) (for models
equipped with the start/stop button).
j
Cut the thread, slide the bobbin winder shaft to
the left and remove the bobbin.
k
Slide the sewing speed controller back to its
original position (for models equipped with the
sewing speed controller).
Memo
When the sewing machine is started or the
handwheel is turned after winding the thread
around the bobbin, the machine will make a
clicking sound; this is not a malfunction.
The needle bar does not move when you slide the
bobbin winding shaft to the right.
For models equipped with the fast bobbin
winding system
a
Place the bobbin on the bobbin winder shaft so
that the spring on the shaft fits into the notch in
the bobbin. Then slide the shaft to the right.
a Notch
b Spring
b
Follow steps a through c of the procedure in
“Winding the bobbin” to pass the thread around
the pretension disk (page 10).
c
Wind the free end of the thread clockwise around
the bobbin five or six times.
d
Pull the thread to the right and pass it through
the slit in the bobbin winder seat.
a Slit (with built-in cutter)
The thread is cut to a suitable length.
e
Slide the sewing speed controller to the right (to
set the speed to fast) (for models equipped with
the sewing speed controller).
CAUTION
Make sure you follow the instructions carefully. If
you do not cut the thread completely, and the bobbin
is wound, when the thread runs low it may tangle
around the bobbin and cause the needle to break.
CAUTION
Not winding the bobbin properly may cause the
thread tension to loosen, and may break the needle.
a Wound evenly
b Wound poorly
a Sewing speed
controller
CAUTION
Be sure to cut the thread as described. If the
bobbin is wound without cutting the thread
using the cutter built into the slit in the bobbin
winder seat, the thread may become tangled in
the bobbin or the needle may bend or break
when the bobbin thread starts to run out.
a Sewing speed
controller
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother KD40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother KD40 in the language / languages: English as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother KD40

Brother KD40 User Manual - German - 72 pages

Brother KD40 User Manual - Dutch - 72 pages

Brother KD40 User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info