631250
15
Zoom out
Zoom in
Previous page
1/67
Next page
7
Changing the Presser Foot
It may be necessary to change the presser foot according to your
sewing needs.
SNAP-ON TYPE
Turn power switch to “O”.
1. Raise the needle to its highest position by turning the balance
wheel toward you (counterclockwise), and raise the presser
foot lever.
2. Release the foot by raising the lever located at the back of the
presser foot holder assembly.
3. Place a different presser foot on the needle plate so that the
bar on the presser foot is in line with the slot on the shank.
4. Lower the presser foot lever and fix the presser foot onto the
shank. If the presser foot is in the correct location, the bar
should snap in.
Changement de pied-de-biche
En fonction des besoins, il peut s’avérer nécessaire de changer le
pied-de-biche.
MODELE A CLIQUET
Mettre l’interrupteur principal sur “O”.
1. Remonter complètement l’aiguille en tournant le volant vers
soi (dans le sens opposé aux aiguilles d’une montre) et
remonter le levier du pied-de-biche.
2. Libérer le pied en levant le levier situé à l’arrière du support.
3. Placer un pied différent sur la plaque à aiguille de telle
manière que la tige du pied-de-biche s’aligne avec la fente de
la fixation.
4. Abaisser le levier du pied-de-biche et fixer le pied sur l’axe. Si
le pied-de-biche est mis correctement, la tige devrait se mettre
en place d’elle même avec un déclic.
Cambio del prensatelas
Según sus necesidades de costura, puede ser necesario cambiar el
prensatelas.
MODELO A PRESIÓN
Coloque el interruptor principal en “O”.
1. Levante la aguja a su posición más alta, girando la ruedecilla
hacia usted (en el sentido contrario al de las manecillas de un
reloj) y levante la palanca del prensatelas.
2. Suelte el prensatelas levantando la palanca que hay en la parte
trasera del soporte.
3. Coloque otro prensatelas en la placa de agujas de tal forma que la
barra del prensatelas quede alineada con la ranura del soporte.
4. Baje la palanca del prensatelas y fije el prensatelas en el soporte.
Si el prensatelas está bien colocado, la barra se entra a presión.
Troca do pé calcador
O pé calcador pode ser trocado conforme suas necessidades de
costura.
ENCAIXE POR PRESSÃO.
Gire o interruptor de força até “O”.
1. Levante a barra do pé calcador. Gire o volante no sentido horário
levantando a agulha até sua posição mais alta.
2. Pressione a alavanca existente atrás do suporte do pé calcador. O
pé calcador em uso se soltará.
3. Coloque o pé calcador que pretende usar, sobre a chapa da agulha
de forma que o pino do pé calcador fique alinhado com a fenda do
suporte.
4. Abaixe a alvanca do calcador para que se enganche no pé calcador.
Se o pé calcador estiver na posição correta, o encaixe se dará
automaticamente.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother JS-23 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother JS-23 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother JS-23

Brother JS-23 User Manual - German, Dutch, French, Italian - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info