631249
33
Zoom out
Zoom in
Previous page
1/84
Next page
22
KNOWING YOUR SEWING MACHINE
OMPELUKONEESEEN TUTUSTUMINEN
CONOZCA SU M
ÁQ
UINA DE COSER
СВЕДЕНИЯ О ШВЕЙНОЙ МАШИНЕ
D
2
1
2
1
NOTE:
The bobbin thread tension has already been adjusted at the factory for
general use. For most sewing applications, no adjustment is needed.
When sewing with thin thread on thin fabrics, the thread tension may
not be adjusted adequately with the upper tension control dial. There-
fore, the thread tension must be adjusted according to the procedure
described below.
C Bobbin tension is too loose.
Loops appear on the surface of the fabric.
Decrease the thread tension by turning the dial to a lower number.
If the result is still not satisfactory, then adjust the bobbin thread
tension as explained in C-1.
C-1 Bobbin
Increase the tension in the bobbin by turning the screw with a
small screwdriver in a clockwise direction. However, do not turn
the screw more than one full turn.
Remember to return the screw to its original setting before start-
ing your next project.
D Correct tension
Correct tension is important since too much or too little tension
may weaken your seams or cause puckers in your fabric.
1 Reverse
2 Surface
VINKKI :
Puolalangan kireys on säädetty tehtaalla normaalikäyttöä varten. Useim-
mat ompelutyöt eivät edellytä kireyden muuttamista.
Ommeltaessa ohuita kankaita ohuella langalla pelkkä ylälangan
kireyden säätö ei kuitenkaan ehkä riitä.
Alalangan kireyttä on tällöin säädettävä alla kuvatulla tavalla.
C Alalanka on liian löysällä.
Lankojen solmukohdat tulevat näkyviin kankaan oikealle puolelle.
Vähennä langan kireyttä kääntämällä säädintä pienempään nu-
meroon.
Ellei tulos ole vieläkään tyydyttävä, säädä alalangan kireyttä koh-
dassa C-1 kuvatulla tavalla.
C-1 Puola
Lisää puolalangan kireyttä kääntämällä ruuvia pienellä
ruuvitaltalla myötäpäivään.
Älä kuitenkaan käännä ruuvia enempää kuin yhden täyden kier-
roksen verran.
Muista kääntää ruuvi takaisin sen alkuperäiseen asentoon ennen
seuraavan ompelutyön aloittamista.
D Oikea kireys
Langan oikea kireys on tärkeä, sillä liian kireä tai löysä langan-
kireys saattaa heikentää saumoja ja vetää kankaan rypyille.
1
Nurja puoli
2
Oikea puoli
NOTA:
La tensión del hilo inferior ya se ha ajustado en fábrica para los usos
comunes. Por lo tanto, para la mayoría de las costuras, no se reque-
rirá ningún ajuste adicional.
Sin embargo, al coser con hilo delgado en tejidos finos, no se puede
ajustar correctamente la tensión del hilo mediante el disco de control
de la tensión superior. En estos casos, la tensión del hilo ha de ser
ajustada de acuerdo con el procedimiento descrito a continuación.
C La tensión del hilo inferior es insuficiente.
Aparecen bagas en la superficie del tejido.
Disminuya la tensión del hilo colocando el disco en un número
inferior. Si el resultado no le conviene aún, ajuste la tensión del
hilo de la canilla tal como se indica en C-1.
C-1 Canilla
Aumente la tensión en la canilla girando el tornillo con un pe-
queño destornillador, en el sentido de las manecillas de un re-
loj. Pero no conviene dar más de una vuelta completa al torni-
llo.
No olvide volver a colocar el tornillo en su posición original an-
tes de empezar otro tipo de costura.
D Tensión correcta
Es importante tener una tensión correcta dado que una tensión
insuficiente o excesiva va a debilitar sus costuras o fruncir el
tejido.
1 Revés
2 Derecho
ПРИМЕЧАНИЕ:
На заводе-производителе натяжение нижней нити настроено
для общего применения. Для большинства вариантов шитья
регулировка не требуется.
При шитье тонкой нитью по тонкой ткани регулятор натяжения
верхней нити может не обеспечивать адекватной настройки.
В таких случаях натяжение нити регулируется согласно
процедуре, описанной ниже.
C Слишком слабое натяжение нижней нити.
На лицевой стороне ткани образуются петли.
Ослабьте натяжение нити, установив регулятор на меньшее
число.
Если вы не довольны результатом, отрегулируйте
натяжение нижней нити, как описано в пункте C-1.
C-1 Шпулька
Увеличьте натяжение нити на шпульке, повернув винт
маленькой отверткой по часовой стрелке.
Однако не поворачивайте винт более чем на один полный
оборот.
Перед началом другой работы не забудьте вернуть винт в
исходное положение.
D Правильное натяжение
Правильное натяжение нити имеет большое значение, так
как слишком сильное или слишком слабое натяжение может
ослабить швы или вызвать образование складок на ткани.
1 Обратная сторона
2 Лицевая сторона
08C713_XE4683-001_P01-24 2008.04.03, 10:5122
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother JS-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother JS-20 in the language / languages: English, Spanish as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info