631137
200
Zoom out
Zoom in
Previous page
1/208
Next page
ERROR MESSAGES
A-30
The bobbin winder safety device has activated. Is the thread
tangled?
This message is displayed when the bobbin is being wound,
and the motor locks because the thread is tangled, etc.
The pockets are full. Delete a pattern. This message is displayed when the memory is full and a
pattern must be deleted.
The safety device has been activated. Is the thread tangled? Is
the needle bent?
This message is displayed when the motor locks due to
tangled thread or for other reasons related to thread delivery.
The shutoff support mode has been activated. Turn off the
machine.
This message appears when the machine is in the shutoff
support mode. Turn off the machine once to start the machine
again. (see page B-26)
The “Start/Stop” button does not operate with the foot
controller attached. Remove the foot controller.
This message is displayed when the “Start/Stop” button is
pushed to sew Utility stitches or Character/Decorative stitches
while the foot controller is connected.
The upper thread may not be threaded correctly. Thread the
upper thread from the beginning.
This message is displayed when it seems that the upper
thread has not been threaded correctly.
The USB media was changed. Do not change the USB media
while it is being read.
This message is displayed when you attempt to select a
pattern after the USB media in which the pattern is saved has
been changed.
There is no needle plate cover. Attach a needle plate cover. This message is displayed when the needle plate cover is not
attached.
This file cannot be used. This message appears if the file format is incompatible with
this machine. Check the list of compatible file formats. (see
page S-94)
This file exceeds the data capacity and cannot be used. Use a
suitable size file.
This message is displayed when the file size exceeds the data
capacity of the machine.
Confirm the file size and format. (see page S-95)
This key cannot be used at this time.
This message is displayed when you press in
the screen other than the Utility Stitch, or press
in the screen other than the Utility Stitch or
Character/Decorative Stitch.
This key does not operate when the needle is down. Raise the
needle and press the key again.
This message is displayed when a key on the LCD display is
touched while the needle is in the down position.
This stitch is not “Dual Feed Mode” compatible. This message appears when the dual feed foot cannot be used
with the current stitch. Select other stitch. (see page B-52)
This USB media cannot be used. This message is displayed when you try to use incompatible
media.
This USB media is incompatible. This message is displayed when you try to use incompatible
USB media. For a list of compatible USB media, visit
“ http://solutions.brother.com
”.
To thread the needle, please remove the fabric from under the
presser foot.
This message is displayed if you press the “Automatic
Threading” button while the dual feed foot is attached and the
presser foot height is 3 mm (1/8 inches) or higher.
Remove the fabric, and then press the “Automatic Threading”
button again.
Transmitting by USB This message is displayed while the USB media is
transmitting.
Turn off the power and replace the needle plate. This message is displayed when you try to sew with a stitch
other than a middle needle position stitch while the single-hole
needle plate is installed.
USB media error This message is displayed when an error occurs with the USB
media.
USB media is not loaded. Load USB media. This message is displayed when you try to recall or save a
pattern while no USB media is loaded.
Use the presser foot lifter button to lower the presser foot. This message is displayed when a button, such as the
“Start/Stop” button, is pushed while the presser foot is raised.
Marks Error Messages Cause/Solution
200


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is VQ2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is VQ2400 in the language / languages: English as an attachment in your email.

The manual is 13,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is VQ2400

Brother Innov-is VQ2400 User Manual - German - 208 pages

Brother Innov-is VQ2400 User Manual - French - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info