631136
195
Zoom out
Zoom in
Previous page
1/208
Next page
TROUBLESHOOTING
Maintenance and Troubleshooting
Appendix A-25
A
2
q
Insert the tabs on the needle plate cover
into the needle plate, and then slide the
cover back on.
r
Check the condition of the needle, and then
install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
* Refer to “CHANGING THE NEEDLE” on page B-49.
Checking machine operations
If the needle plate has been removed, check
machine operations to confirm that installation has
been completed correctly.
a
Turn on the machine.
b
Select .
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides
to check that the needle falls at the center
of the hole in the needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with
step
m in “Removing the fabric from the machine” on
page A-24.
a Hole in the needle plate
b Handwheel
d
Select zigzag stitch . At this time,
increase the stitch length and width to their
maximum settings.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the
needle bar and feed dogs operate correctly.
If the needle or feed dogs contact the needle plate, the
machine may be malfunctioning; therefore, contact
your dealer or nearest authorized service center.
f
Turn off the machine, and then install the
bobbin and presser foot.
* Refer to “Setting the Bobbin” and “CHANGING THE
PRESSER FOOT” on page B-47.
g
Correctly thread the machine.
* For details on the machine, refer to “Upper
Threading” on page B-40.
h
Perform trial sewing with normal fabric.
Note
If the needle plate has been removed it is
especially important to reinstall the needle
plate and tighten the screws prior to
installing the bobbin case.
CAUTION
Never use bent needles. Bent needles can
easily break, possibly resulting in injuries.
Note
After completing this procedure, continue
with the following procedure in “Checking
machine operations” to check that the
machine is operating correctly.
Memo
Since the needle may have been damaged
when the fabric was caught in the machine,
we recommend replacing it with a new one.
Note
Do not yet install the presser foot and
thread.
Note
The thread may have become tangled as a
result of incorrect upper threading. Make
sure that the machine is correctly threaded.
Note
Incorrect sewing may be the result of
incorrect upper threading or sewing thin
fabrics. If there are poor results from the
trial sewing, check the upper threading or
the type of fabric being used.
195


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is VQ2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is VQ2 in the language / languages: English as an attachment in your email.

The manual is 13,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is VQ2

Brother Innov-is VQ2 User Manual - German - 208 pages

Brother Innov-is VQ2 User Manual - French - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info