718770
172
Zoom out
Zoom in
Previous page
1/180
Next page
ERROR MESSAGES
A-22
If the machine is not properly set and the “Start/Stop” button is pressed, or if the operation procedure is
incorrect, the machine does not start. An alarm sounds and an error message is displayed on the LCD. If
an error message displays, follow the instructions in the message.
Below is an explanation of error messages. Refer to these when necessary (if you press or do the
operation correctly while the error message is displayed, the message disappears).
Specifying with
sensor pen cannot be
done accurately
The sensor pen has not been calibrated. Before using the sensor pen for the first time,
be sure to calibrate it.
B-56
The pen is being held differently than when it
was calibrated.
When using the sensor pen, be sure to hold it
at the same angle as when it was calibrated.
The specification location may be misaligned
if the pen is held at a slightly different angle.
In this case, make fine adjustments after
making the selection.
B-56
CAUTION
This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the
upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,
the machine may feed the fabric even if the needle is raised. This is due to the needle bar release
mechanism. At these times, the machine will make a sound different from what is made during normal
sewing. This is not the sign of a malfunction.
If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the instructions for operating the machine correctly.
ERROR MESSAGES
CAUTION
Be sure to rethread the machine. If you press the “Start/Stop” button without rethreading the machine,
the thread tension may be wrong or the needle may break and cause injury.
Marks Error Messages Cause/Solution
A malfunction occurred.Turn the machine off, then on again. This message is displayed if some malfunction occurs.
Attach the embroidery frame. This message appears if the embroidery frame is not attached
when you press in the embroidery screen. (see page
B-58)
Check and rethread the upper thread. This message is displayed when the upper thread is broken or
not threaded correctly, and the “Start/Stop” button is pressed.
Data volume is too large for this pattern. This message is displayed when the patterns you are editing
take up too much memory, or if you are editing too many
patterns for the memory.
Failed to save file. This message appears when you try to save more than 100
settings screen image files in the USB media. In this case,
delete a file from the USB media or use different USB media.
(see page B-28)
Lower the presser foot lever. This message is displayed when the “Presser Foot Lifter”
button is pushed while the presser foot lever is raised/the
needle is lowered.
Move the sensor pen away from the currently marked position. This message appears when you press down the sensor pen
tip before pressing and keep pressing for the certain
period. Move the sensor pen away from the current position.
Problem Cause Solution Page
172


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is V3 LE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is V3 LE in the language / languages: English as an attachment in your email.

The manual is 14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is V3 LE

Brother Innov-is V3 LE User Manual - German - 180 pages

Brother Innov-is V3 LE User Manual - Dutch - 180 pages

Brother Innov-is V3 LE User Manual - French - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info