618038
92
Zoom out
Zoom in
Previous page
1/100
Next page
Troubleshooting
A-8
Upper thread
breaks.
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly. B-19
Knotted or tangled thread is being used. Remove any knots or tangles.
Upper thread tension is too strong. Adjust the thread tension. E-26
Thread is tangled. Use scissors, etc., to cut the tangled thread and
remove it from the race, etc.
A-2
Needle is turned, bent or the point is dull. Replace the needle. B-23
Needle is installed incorrectly. Reinstall the needle correctly. B-23
There are scratches near the hole in the
embroidery foot.
Replace the embroidery foot, or consult your
authorized Brother dealer.
A-5
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized Brother dealer.
A-2
Using improper needle or thread for the
selected fabric.
Check the information about the needle and
thread to be used.
B-23
While embroidering, the thread became knotted
or tangled.
Rethread upper and lower thread. B-17, B-19
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-14
The thread is
tangled on the
wrong side of the
fabric.
Upper threading is incorrect. Check the steps for threading the machine and
rethread the machine. Be sure that the
embroidery foot is in the raised position when
threading the machine so that the upper thread
sets properly in the upper tension.
B-19
Using improper needle or thread for the
selected fabric.
Check the information about the needle and
thread to be used.
B-23
The upper thread is
too tight.
The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-17
Bobbin thread
breaks.
Bobbin is set incorrectly. Reset the bobbin correctly. B-17
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-17
There are scratches on the bobbin or it doesn’t
rotate properly.
Replace the bobbin. B-14
Thread is tangled. Use scissors, etc. to cut the tangled thread and
remove it from the race, etc.
A-2
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-14
Fabric puckers.
There is a mistake in the upper or bobbin
threading.
Check the steps for threading the machine and
rethread it correctly.
B-19
Spool cap is set incorrectly. Check the method for attaching the spool cap,
then reattach the spool cap.
B-14
Needle is turned, bent or the point is dull. Replace the needle. B-23
Skipped stitches
Machine is threaded incorrectly. Check the steps for threading the machine and
rethread it correctly.
B-19
Needle is turned, bent or the point is dull. Replace the needle. B-23
Needle is installed incorrectly. Reinstall the needle correctly. B-23
The needle is worn/damaged. Replace the needle. B-23
Dust or lint has collected under the needle
plate.
Remove the dust or lint with the brush. A-2
Symptom Probable Cause Remedy Reference
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is NV800E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is NV800E in the language / languages: English as an attachment in your email.

The manual is 9,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is NV800E

Brother Innov-is NV800E User Manual - German - 100 pages

Brother Innov-is NV800E User Manual - Dutch - 100 pages

Brother Innov-is NV800E User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info