618041
73
Zoom out
Zoom in
Previous page
1/144
Next page
Overcasting Stitches
Sewing S-13
UTILITY STITCHES
S
a
Remove the presser foot.
b
Hook the connecting fork of the side cutter onto the
needle clamp screw.
1 Connecting fork
2 Needle clamp screw
c
Position the side cutter so that side cutter pin is aligned
with the notch in the presser foot holder, and then
slowly lower the presser foot lever.
1 Notch in presser foot holder
2 Pin
d
Raise the presser foot lever to check that the side
cutter is securely attached.
e
Pass the upper thread under the side cutter, and then
pull it out toward the rear of the machine.
f
Select a stitch.
g
Make a cut of about 2 cm (3/4 inch) long in the fabric
at the beginning of the stitching.
1 2 cm (3/4 inch)
h
Position the fabric in the side cutter.
The cut in the fabric should be positioned over the
guide plate of the side cutter.
1 Guide plate
If the fabric is not positioned correctly, the fabric will
not be cut.
i
Lower the presser foot lever, and then start sewing.
A seam allowance is cut while the stitching is sewn.
If the stitching is sewn in a straight line , the seam
allowance will be about 5 mm (3/16 inch).
1 5 mm (3/16 inch)
Note
When it is hard to set under the presser foot
holder, fit the pin on the side cutter into the notch
of the presser foot holder raising up the presser
foot lever higher.
b
a
b
a
Memo
The side cutter can cut as much as one layer of
13-oz. denim.
After using the side cutter, clean it by removing
any lint or dust.
If the side cutter can no longer cut fabric, use a
piece of cloth to apply a small amount of oil to the
cutting edge of the cutter.
1
a
1
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is NV1300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is NV1300 in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is NV1300

Brother Innov-is NV1300 User Manual - German - 144 pages

Brother Innov-is NV1300 User Manual - Dutch - 144 pages

Brother Innov-is NV1300 User Manual - French - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info