618041
11
Zoom out
Zoom in
Previous page
1/144
Next page
Names of Machine Parts and Their Functions
GETTING READY
Basic operations B-3
B
Needle and presser foot section
1 Needle bar thread guide
Pass the upper thread through the needle bar thread guide.
2 Needle plate
The needle plate is marked with guides for sewing straight
seams.
3 Needle plate cover
Remove the needle plate cover to clean the bobbin case and
race.
4 Bobbin cover/bobbin case
Remove the bobbin cover, and then insert the bobbin into the
bobbin case.
5 Feed dogs
The feed dogs feed the fabric in the sewing direction.
6 Presser foot
The presser foot applies pressure consistently on the fabric as
the sewing takes place. Attach the appropriate presser foot for
the selected stitch.
7 Presser foot holder
The presser foot is attached onto the presser foot holder.
8 Presser foot holder screw
Use the presser foot holder screw to hold the presser foot in
place. (page B-32)
9 Buttonhole lever
Lower the buttonhole lever when sewing buttonholes and bar
tacks or when darning.
Operation buttons
1 “Start/Stop” button
Press the “Start/Stop” button to start or stop sewing. The
machine stitches at a slow speed at the beginning of sewing
while the button is pressed. When sewing is stopped, the
needle is lowered in the fabric. For details, refer to “STARTING
TO SEW” on page B-33.
The button changes color according to the machine’s
operation mode.
2 Reverse stitch button
For straight, zigzag, and elastic zigzag stitch patterns that use
reverse stitches, the machine will sew reverse stitches at low
speed only while holding down the Reverse stitch button. The
stitches are sewn in the opposite position.
For other stitches, use this button to sew reinforcement
stitches at the beginning and end of sewing. Press and hold
this button, and the machine sews 3 stitches in the same spot
and stops automatically. (page B-37)
3 Reinforcement stitch button
Use this button to sew a single stitch repeatedly and tie-off.
For character/decorative stitches, press this button to end with
a full stitch instead of at a mid-point. The LED light beside this
button lights up while the machine is sewing a full motif, and
automatically turns off when the sewing is stopped. (page B-
37)
4 Needle position button
Press the needle position button to raise or lower the needle.
Pressing the button twice sews one stitch.
5 Thread cutter button
Press the thread cutter button after sewing is stopped to cut
both the upper and the bobbin threads. For details, refer to
step
j under “Sewing a stitch” section on page B-35.
6 Presser foot lifter button
(Equipped on some models. Refer to page B-8)
Press this button to lower the presser foot and apply pressure
to the fabric. Press this button again to raise the presser foot.
7 Sewing speed controller
Slide the sewing speed controller to adjust the sewing speed.
i
b
a
c
d
e
f
g
h
Green: The machine is ready to sew or is sewing.
Red: The machine can not sew.
Orange: The machine is winding the bobbin thread, or
the bobbin winder shaft is moved to the right
side.
CAUTION
Do not press (Thread cutter button) after
the threads have already been cut, otherwise
the needle may break, the threads may
become tangled or damage to the machine
may occur.
bcdef
a
g
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is NV1300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is NV1300 in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is NV1300

Brother Innov-is NV1300 User Manual - German - 144 pages

Brother Innov-is NV1300 User Manual - Dutch - 144 pages

Brother Innov-is NV1300 User Manual - French - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info