613641
137
Zoom out
Zoom in
Previous page
1/144
Next page
Troubleshooting
Appendix A-17
MAINTENANCE AND TROUBLESHOOTING
A
After sewing
Error messages
If the “Start/Stop” button is pressed before the machine is correctly set up or if an operation is performed incorrectly, an error
message appears in the LCD. Follow the instructions that appear. The message will disappear if or is pressed while the
message is displayed.
Symptom Probable Cause Remedy Reference
Thread tension is
incorrect.
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-21
Bobbin is set incorrectly.
Reset the bobbin. (If needle plate was removed,
reinstall needle plate and tighten screws prior to
installing bobbin case. Check to make sure
needle enter through the center of needle plate
opening.)
B-18, A-2
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-28
Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. B-32
Thread tension is set incorrectly. Adjust the thread tension. B-40, A-6
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-15
Needle is turned, bent or the point is dull. Replace the needle. B-29
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-15
Character or
decorative patterns
are misaligned.
Pattern adjustment settings were set incorrectly. Revise the pattern adjustment settings. D-10
Pattern does not
turn out.
Wrong presser foot was used. Attach the correct presser foot. B-32
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material. S-4, D-3
Thread tension is set incorrectly. Adjust the thread tension. B-40, A-6
Fabric was pulled, pushed or fed at an angle
while it was being sewn.
Sew while guiding the fabric with your hands so
that the fabric is fed in a straight line.
B-35
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
A-8
Error Messages Cause/Solution
1
This message is displayed when the sewing speed controller is set to control the
zigzag stitch width, and the “Start/Stop” button is pressed. Set (Width control)
to “OFF” (refer to page B-12), or use the foot controller to operate the machine.
2
This message is displayed when (Twin needle) is set to “ON”, and a stitch pattern
that cannot be sewn with the twin needle is selected.
137


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is NV1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is NV1100 in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is NV1100

Brother Innov-is NV1100 Quick start guide - English, German - 32 pages

Brother Innov-is NV1100 User Manual - German - 144 pages

Brother Innov-is NV1100 Quick start guide - Dutch - 32 pages

Brother Innov-is NV1100 User Manual - Dutch - 144 pages

Brother Innov-is NV1100 Quick start guide - French - 32 pages

Brother Innov-is NV1100 User Manual - French - 144 pages

Brother Innov-is NV1100 Quick start guide - Italian, Spanish - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info