718767
109
Zoom out
Zoom in
Previous page
1/120
Next page
Troubleshooting
Appendix A-13
MAINTENANCE AND TROUBLESHOOTING
A
While sewing
The sewing light
does not come on.
The sewing light is damaged.
Contact your authorized Brother dealer or the
nearest Brother authorized service center.
(Light) is set to “OFF” in the settings
screen.
Change the setting to “ON”. B-11
Symptom Probable Cause Remedy Reference
Machine does not
operate.
“Start/Stop” button was not pressed. Press the “Start/Stop” button. B-34
The bobbin winder shaft is pushed to the right. Move the bobbin winder shaft to the left. B-14
There is no pattern selected. Select a pattern. B-34
Presser foot is not lowered. Lower the presser foot. B-34
“Start/Stop” button was pushed with the foot
controller attached.
Remove the foot controller, or use the foot
controller to operate the machine.
B-36
The “Start/Stop” button was pressed while the
machine is set for the sewing speed controller
to control the zigzag stitch width.
Use the foot controller instead of the “Start/
Stop” button to operate the machine, or set the
(Width control) to “OFF” in the settings
screen.
B-11, B-36
Needle breaks.
Needle is installed incorrectly. Reinstall the needle correctly. B-28
Needle clamp screw is not tightened. Tighten the needle clamp screw. B-28
Needle is turned or bent. Replace the needle. B-28
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-27
Wrong presser foot was used. Use the recommended presser foot. B-31
Upper thread tension is too tight. Adjust the thread tension. B-40
Fabric is pulled during sewing. Do not pull the fabric during sewing.
Spool cap is set incorrectly.
Check the method for attaching the spool cap,
then reattach the spool cap.
B-14
There are scratches around the opening in the
needle plate.
* There is a notch on the left side of the
opening in the needle plate. This is not a
scratch.
1 Notch
Replace the needle plate, or consult your
authorized Brother dealer.
A-7
There are scratches around the opening in the
presser foot.
Replace the presser foot, or consult your
authorized Brother dealer.
B-30
There are scratches on the bobbin case.
Replace the bobbin case, or consult your
authorized Brother dealer.
A-2
Symptom Probable Cause Remedy Reference
a
109


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is NV1040SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is NV1040SE in the language / languages: English as an attachment in your email.

The manual is 2,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is NV1040SE

Brother Innov-is NV1040SE User Manual - German - 116 pages

Brother Innov-is NV1040SE User Manual - Dutch - 116 pages

Brother Innov-is NV1040SE User Manual - French - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info