718769

Brother Innov-is M280D Manual

61
Zoom out
Zoom in
Previous page
1/100
Next page
Embroidering Preparation
59
EMBROIDERY
4
Follow the steps below to prepare the machine for
embroidery.
Attaching the Embroidery Foot
a
Press (Needle position button) to raise the needle.
b
Press .
The screen changes, and all keys and operation
buttons are locked (except ).
c
Remove the presser foot and presser foot holder.
• For details, refer to “Replacing the Presser Foot” on
page 23.
d
Hold the embroidery foot “Q” with your right hand, as
shown.
Hold the embroidery foot with your index finger
wrapped around the lever at the back of the foot.
1 Lever
2 Embroidery foot bar
Chapter 4
EMBROIDERY
Embroidering Preparation
Step
#
Aim Action Page
1 Presser foot
attachment
Attach embroidery foot “Q”. 59
2 Checking the
needle
Use needle 75/11 for
embroidery.
22
3 Embroidery unit
attachment
Attach the embroidery unit. 60
4Bobbin thread
setup
For the bobbin thread, wind
embroidery bobbin thread and
set it in place.
13
5Fabric
preparation
Attach a stabilizer material to
the fabric, and hoop it in the
embroidery frame.
62
6Embroidery
frame
attachment
Attach the embroidery frame
to the embroidery unit.
64
7 Pattern selection Turn the main power to on,
and select an embroidery
pattern.
65
8 Checking the
layout
Check and adjust the size and
position of the embroidery.
67
9Embroidery
thread setup
Set up embroidery thread
according to the pattern.
68
Step 3
Step 1, 2
Step 5
Step 6
Step 4
Step 7, 8
Step 9
CAUTION
• Be sure to use embroidery foot when doing
embroidery. Using another presser foot may
cause the needle to strike the presser foot,
causing the needle to bend or break and
possibly cause injury.
b
a
… 61 …


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-m280d

Reset search

  • bonjour
    je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03

    Reply Report abuse

  • bonjour
    je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
    Merci bonne journée Submitted on 3-9-2022 at 10:38

    Reply Report abuse

  • message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is M280D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info