718744
35
Zoom out
Zoom in
Previous page
1/212
Next page
Upper Threading
GETTING READY
Basic operations B-25
B
k
Slide the thread behind the needle bar thread guide.
The thread can easily be slid behind the needle bar
thread guide by holding the thread in your left hand,
then feeding the thread with your right hand, as shown.
Make sure that the thread is passed through to the left of
the tab of the needle bar thread guide.
1 Needle bar thread guide
2 Tab
l
Raise the presser foot lever.
Threading the needle
a
Pull the end of the thread, which has been passed
through the needle bar thread guide, to the left, then
pass the thread through the notch of the threader
thread guide a, and then firmly pull the thread from
the front and insert it into the slit of the threader
thread guide disk marked “7” all the way b.
Make sure that the thread passes through the notch of
the threader thread guide.
1 Notch of the threader thread guide
2 Threader thread guide disk
b
Cut the thread with the thread cutter on the left side of
the machine.
1 Cutter
c
Lower the presser foot lever to lower the presser foot.
1 Presser foot lever
Memo
The needle threader can be used with machine
needles 75/11 through 100/16.
The needle threader cannot be used with the wing
needle or the twin needle.
When thread such as transparent nylon
monofilament or specialty threads are used it is
not recommended to use the needle threader.
If the needle threader cannot be used, refer to
“Threading the needle manually (without using the
needle threader)” on page B-26.
1
2
2
1
a
b
Note
If the thread is pulled through and cannot be cut
correctly, lower the presser foot lever so that the
thread is held in place before cutting the thread.
If this operation is performed, skip step
c.
When using thread that quickly winds off the
spool, such as metallic thread, it may be difficult
to thread the needle if the thread is cut.
Therefore, instead of using the thread cutter, pull
out about 8 cm (approx. 3 inches) of thread after
passing it through the threader thread guide
disks (marked “7”).
1 8 cm (approx. 3 inches) or more
1
1
1
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is F480 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is F480 in the language / languages: English as an attachment in your email.

The manual is 13,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is F480

Brother Innov-is F480 User Manual - German - 212 pages

Brother Innov-is F480 User Manual - Dutch - 212 pages

Brother Innov-is F480 User Manual - French - 212 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info