718743
123
Zoom out
Zoom in
Previous page
1/144
Next page
Troubleshooting
Appendix A-5
MAINTENANCE AND TROUBLESHOOTING
A
Pull the thread to pass it through the slit in the needle
plate cover, then cut it with the cutter.
3 Slit
4 Cutter
Sewing with the correct thread tension is possible after
the bobbin has been correctly installed in the bobbin
case.
e
Press to unlock all keys and buttons.
Tangled thread on wrong side of fabric
Symptom
The thread becomes tangled on the wrong side of the
fabric.
After starting sewing, a rattling noise is made and
sewing cannot continue.
Looking under the fabric, there is tangled thread in
the bobbin case.
Cause
Incorrect upper threading
If the upper thread is incorrectly threaded, the upper
thread passed through the fabric cannot be firmly pulled
up and the upper thread becomes tangled in the bobbin
case, causing a rattling noise.
Remedy/check details
Remove the tangled thread, and then correct the upper
threading.
a
Remove the tangled thread. If it cannot be removed,
cut the thread with scissors.
For details, refer to “Cleaning the race” on page A-2.
b
Remove the upper thread from the machine.
If the bobbin was removed from the bobbin case,
refer to “Installing the bobbin” in the “Basic
operations” section and “Remedy/check details” in
the section “Upper thread tightened up” on page A-4
to correctly install the bobbin.
c
Refer to the following steps to correct the upper
threading. Raise the presser foot using the presser foot
lever.
1 Presser foot lever
The upper thread shutter opens so the machine can
be threaded.
If the presser foot is not raised, the machine cannot
be threaded correctly.
d
Press (Needle position button) once or twice to
raise the needle.
The needle is correctly raised when the mark on the
handwheel is at the top, as shown below. Check the
handwheel and, if this mark is not at this position,
press (Needle position button) until it is.
1 Mark on handwheel
e
While holding the thread lightly with your right hand,
pull the thread with your left hand, and then pass the
thread behind the thread guide cover and to the front.
1 Thread guide cover
1
1
1
123


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is F460 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is F460 in the language / languages: English as an attachment in your email.

The manual is 7,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is F460

Brother Innov-is F460 User Manual - German - 144 pages

Brother Innov-is F460 User Manual - Dutch - 144 pages

Brother Innov-is F460 User Manual - French - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info