718739
113
Zoom out
Zoom in
Previous page
1/132
Next page
Troubleshooting
Appendix A-11
MAINTENANCE AND TROUBLESHOOTING
A
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the fabric from the machine” on
page A-8.
1 Opening in the needle plate
2 Handwheel
d
Select stitch . At this time, increase the stitch length
and width to their maximum settings.
For details on changing the settings, refer to “Setting
the stitch width” and “Setting the stitch length” in the
“Basic operations” section.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle bar and
feed dogs operate correctly.
If the needle or feed dogs contact the needle plate, the
machine may be malfunctioning; therefore, contact
your nearest Brother authorized service center.
f
Turn off the machine, and then install the bobbin and
presser foot.
Refer to “Installing the bobbin” and “Replacing the
presser foot” in the “Basic operations” section.
g
Correctly thread the machine.
For details on threading the machine, refer to “Upper
Threading” in the “Basic operations” section.
h
Perform trial sewing with cotton fabric.
If the thread becomes tangled under the
bobbin winder seat
If the bobbin winding starts when the thread is not passed
under the pretension disk of the bobbin-winding thread guide
correctly, the thread may become tangled under the bobbin
winder seat.
In such a case, wind off the thread according to the following
procedure.
1 Thread
2 Bobbin winder seat
Memo
The thread may have become tangled as a result
of incorrect upper threading. Make sure that the
machine is correctly threaded.
Note
Incorrect sewing may be the result of incorrect
upper threading or sewing thin fabrics. If there
are poor results from the trial sewing, check the
upper threading or the type of fabric being used.
Memo
The shape of the bobbin winder guide post will
differ depending on your model; however, this
should not affect the operating procedure.
This manual describes the procedure for models
with a key-shaped bobbin winder guide post.
1 Bobbin winder guide post (oval)
1 Bobbin winder guide post (key)
1
2
1
1
113


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is F410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is F410 in the language / languages: English as an attachment in your email.

The manual is 3,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is F410

Brother Innov-is F410 User Manual - German - 132 pages

Brother Innov-is F410 User Manual - Dutch - 132 pages

Brother Innov-is F410 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info