718735
62
Zoom out
Zoom in
Previous page
1/72
Next page
Troubleshooting
60
l
Remove any threads in the race and around the feed
dogs.
m
Turn the handwheel to raise the feed dogs.
n
Align the two screw holes in the needle plate with the
two holes at the needle plate mounting base, and then
fit the needle plate onto the machine.
o
Lightly finger-tighten the screw on the right side of the
needle plate. Then, use the disc-shaped screwdriver to
firmly tighten the screw on the left side. Finally, firmly
tighten the screw on the right side.
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1 Correct position of feed dogs
2 Incorrect position of feed dogs
p
Insert the bobbin case by following step k in
“Cleaning the race” on page 55.
q
Attach the needle plate cover according to step l in
“Cleaning the race” on page 55.
r
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
Refer to “Checking the needle” on page 20 and
“Replacing the needle” on page 20.
Checking machine operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select stitch .
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the fabric from the machine” on
page 59.
d
Select stitch . At this time, increase the stitch length
and width to their maximum settings.
For details on changing the settings, refer to “Setting
the stitch width” on page 27 and “Setting the stitch
length” on page 27.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle bar and
feed dogs operate correctly.
If the needle or feed dogs contact the needle plate, the
machine may be malfunctioning; therefore, contact
your nearest Brother authorized service center.
f
Turn off the machine, and then install the bobbin and
presser foot.
Never use a scratched or damaged presser foot.
Otherwise, the needle may break, or sewing
performance may suffer.
Refer to “Installing the bobbin” on page 14 and
“Replacing the presser foot” on page 21.
g
Correctly thread the machine.
For details on threading the machine, refer to “Upper
Threading” on page 15.
h
Perform trial sewing with cotton fabric.
Memo
Since the needle may have been damaged when the
fabric was caught in the machine, we recommend
replacing it with a new one.
Note
Do not yet install the presser foot and thread.
a
b
1 Opening in the needle
plate
2 Handwheel
Note
Incorrect sewing may be the result of incorrect upper
threading or sewing thin fabrics. If there are poor results
from the trial sewing, check the upper threading or the
type of fabric being used.
a
b
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A60 SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A60 SE in the language / languages: English as an attachment in your email.

The manual is 27,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A60 SE

Brother Innov-is A60 SE User Manual - German - 72 pages

Brother Innov-is A60 SE User Manual - Dutch - 72 pages

Brother Innov-is A60 SE User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info