718735
19
Zoom out
Zoom in
Previous page
1/72
Next page
Upper Threading
GETTING READY
17
1
k
Check that the needle and thread are compatible with
the needle threader. If they are compatible, continue
with the next step.
The needle threader can be used with machine
needles 75/11 through 100/16.
The needle threader cannot be used with the wing
needle or the twin needle.
When thread such as transparent nylon
monofilament or specialty threads are used, it is not
recommended to use the needle threader.
If the needle threader cannot be used, insert the
thread through the eye of the needle from front to
back by hand. At this time, be sure that the machine
has been turned off as described in step
d.
l
Pull the end of the thread, which has been passed
through the needle bar thread guide, to the left, pass
the thread under the notch, and then firmly pull the
thread to fully insert it from front to back into the slit
of the thread guide disk (marked “7”).
1 Notch of the threader thread guide
2 Threader thread guide disk
m
Cut the thread with the thread cutter on the left side of
the machine.
n
Lower the presser foot lever to lower the presser foot.
o
Lower the needle threader lever on the left side of the
machine as much as possible to make the hook turn.
After the threader thread guide disk is lowered (1), the
hook turns (2).
1 Needle threader lever
2 Needle
3 Hook
p
Raise the needle threader lever slowly.
q
Carefully pull the end of thread that was passed
through the eye of the needle.
If the needle was not completely threaded, but a loop in
the thread was formed in the eye of the needle, carefully
pull the loop through the eye of the needle to pull out
the end of the thread.
Note
If the thread is pulled through and cannot be cut
correctly, lower the presser foot lever so that the thread
is held in place before cutting the thread. If this
operation is performed, proceed to step
o.
When using thread that quickly winds off the spool,
such as metallic thread, it may be difficult to thread the
needle if the thread is cut.
Therefore, instead of using the thread cutter, pull out
about 8 cm (approx. 3 inches) of thread after passing it
through the threader thread guide disk (marked “7”).
1
2
Note
If the needle is not raised to it's highest position, the
needle threader cannot thread the needle. Turn
handwheel counterclockwise until the needle is at its
highest position. The needle is correctly raised when the
mark on the handwheel is at the top, as shown under
step
c on page 15.
1
2
3
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A60 SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A60 SE in the language / languages: English as an attachment in your email.

The manual is 27,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A60 SE

Brother Innov-is A60 SE User Manual - German - 72 pages

Brother Innov-is A60 SE User Manual - Dutch - 72 pages

Brother Innov-is A60 SE User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info