718735
7
Zoom out
Zoom in
Previous page
1/72
Next page
Names of Machine Parts
GETTING READY
5
1
Main parts
The appearance of the machine differs depending on the
model.
1 Bobbin winding thread guide and pretension disk
(page 13)
2 Thread guide (page 13)
3 Spool cap (page 12)
4 Spool pin (page 12)
5 Hole for extra spool pin
This holds an extra spool pin for sewing with the twin needle.
(page 52) This is not a hole for lubrication. Do not insert oil into
this hole.
6 Bobbin winder (page 12)
7 LCD (liquid crystal display) (page 10)
8 Operation keys (page 6)
The operation keys differ depending on the model.
9 Stitch pattern display window (page 23)
(Equipped on 16 stitches model)
0 Stitch pattern selection dial (page 23)
A Operation buttons and sewing speed controller
(page 6)
B Flat bed attachment (page 7, 29)
C Thread cutter (page 17)
D Needle threader lever (page 17)
E Thread tension dial (page 27)
F Handwheel
Turn the handwheel toward you (counterclockwise) to raise and
lower the needle to sew one stitch.
G Thread guide cover (page 13)
H Handle
Carry the machine by its handle when transporting.
I Presser foot lever
Raise and lower the presser foot lever to raise and lower the
presser foot.
J Feed dog position switch
Use the feed dog position switch to raise and lower the feed
dogs. (page 48)
K Main power switch (page 9)
L Power supply jack (page 9)
M Foot controller (page 24)
N Foot controller jack (page 24)
O Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.
Needle and presser foot section
1 Needle bar thread guide (page 16)
2 Needle plate (page 29)
3 Needle plate cover (page 14)
4 Bobbin cover/bobbin case (page 14, 56)
5 Feed dogs
The feed dogs feed the fabric in the sewing direction.
6 Presser foot
The presser foot applies pressure consistently on the fabric as
the sewing takes place. Attach the appropriate presser foot for
the selected stitch.
7 Presser foot holder (page 22)
8 Presser foot holder screw (page 22)
9 Buttonhole lever (page 42)
Chapter 1
GETTING READY
Names of Machine Parts
a
b
c
d
e
f
g
h
k
l
m
j
i
n
o
p
q
r
s
t
u
v
w
x
y
i
b
a
c
d
e
f
g
h
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A60 SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A60 SE in the language / languages: English as an attachment in your email.

The manual is 27,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A60 SE

Brother Innov-is A60 SE User Manual - German - 72 pages

Brother Innov-is A60 SE User Manual - Dutch - 72 pages

Brother Innov-is A60 SE User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info