718716
16
Zoom out
Zoom in
Previous page
1/72
Next page
Winding/Installing the Bobbin
14
l
Slide the sewing speed controller to desired sewing
speed position.
m
Remove the spool for the bobbin thread from the spool
pin.
Installing the bobbin
Install the bobbin wound with thread.
You can begin sewing immediately without pulling up the
bobbin thread by simply inserting the bobbin in the bobbin
case and guiding the thread through the slit in the needle
plate cover.
a
Turn on the machine.
b
Press (Needle position button) once or twice to
raise the needle.
c
Turn off the machine.
d
Raise the presser foot lever.
e
Slide the bobbin cover latch to the right and remove
the bobbin cover.
f
Place the bobbin in the bobbin case so that the thread
unwinds to the left.
g
Lightly hold down the bobbin with your right hand
(1), and then guide the end of the thread around the
tab of the needle plate cover with your left hand (2).
Memo
If the threads will be pulled to create gathers or the
thread at the beginning of sewing will be finished, for
example, when free motion quilting, first pull up the
bobbin thread.
For details, refer to “Pulling up the bobbin thread” on
page 18.
CAUTION
Use a bobbin that has been correctly wound
with thread, otherwise the needle may break
or the thread tension will be incorrect.
Before inserting or changing the bobbin, be
sure to turn off the machine, otherwise injuries
may occur if the “Start/Stop” button or any
other button is pressed and the machine starts
operating.
Memo
For the correct winding direction of the bobbin thread,
be sure to place the bobbin into the bobbin case in the
same orientation that it was on the bobbin winder shaft.
The “b” mark on one side of the bobbin included with
this machine can be used as a reference.
1 Tab
CAUTION
Be sure to hold down the bobbin with your
finger and unwind the bobbin thread
correctly, otherwise the thread may break or
the thread tension will be incorrect.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A16 in the language / languages: English as an attachment in your email.

The manual is 27,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A16

Brother Innov-is A16 User Manual - German - 72 pages

Brother Innov-is A16 User Manual - Dutch - 72 pages

Brother Innov-is A16 User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info