613557
165
Zoom out
Zoom in
Previous page
1/176
Next page
Troubleshooting 163
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
4
A high-pitched
noise is made while
sewing.
Dust has accumulated in the feed
dogs or in the bobbin case.
Clean the race. page 149
The upper thread was not threaded
correctly.
Correct the upper threading. page 28
The bobbin case is scratched, or has
a burr on it.
Replace the bobbin case. Contact
your dealer or the nearest
authorized service center.
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 22
The needle threader
cannot be used.
The needle has not been raised to the
correct position.
Press the “Needle Position”
button.
page 31
The needle is incorrectly installed. Correctly install the needle. page 39
The stitch is not
sewn correctly.
The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
Attach the presser foot that is
appropriate for the type of stitch
that you wish to sew.
page 138
The thread tension is incorrect.
Adjust the tension of the upper
thread.
page 57
The thread is tangled, for example, in
the bobbin case.
Remove the tangle thread. If the
thread is tangled in the bobbin
case, clean the race.
page 149
The fabric does not
feed.
The feed dogs are lowered.
Slide the drop feed lever to the
right. (as seen from the rear of the
machine)
page 105
The stitch is too short. Lengthen the stitch length. page 60
The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
Attach the presser foot that is
appropriate for the type of stitch
that you wish to sew.
page 138
The pressure of the presser foot is
weak.
Turn the presser foot pressure dial
to the left to increase the pressure
of the presser foot.
page 43
The thread is tangled, for example, in
the bobbin case.
Remove the tangle thread. If the
thread is tangled in the bobbin
case, clean the race.
page 149
Zigzag foot “J” is slanted on a thick
seam at the beginning of stitching.
Use the presser foot locking pin
(black button on the left side) on
zigzag foot “J” to keep the presser
foot level while sewing.
page 67
The sewing lamp
does not come on.
The sewing lamp is damaged.
Contact your dealer or the nearest
authorized service center.
Nothing appears in
the LCD.
The brightness of the LCD is either
too light or too dark.
Adjust the brightness of the LCD. page 166
Symptom Probable Cause Remedy Reference
165


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 610 in the language / languages: English as an attachment in your email.

The manual is 5,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 610

Brother Innov-is 610 Quick start guide - All languages - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info