613441
252
Zoom out
Zoom in
Previous page
1/276
Next page
TROUBLESHOOTING
240
TROUBLESHOOTING
If you have a minor problem with your sewing machine, check the following solutions. If the solutions
suggested do not correct the problem, contact your authorized dealer. You can also press then
for advice about minor sewing problems during sewing. Press at any time to return to
the original screen.
Problem Cause Solution Page
Upper thread breaks Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly. 29
Thread is knotted or tangled. Rethread upper and lower thread. 26, 29
Thread is too thick for the needle. Check needle and thread combinations. 41
Upper thread tension is too strong. Adjust the thread tension. 50, 174
Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
Needle is turned, bent or the point is dull. Replace the needle. 39
Needle is installed incorrectly. Reinstall the needle correctly. 39
There are scratches near the hole of the needle
plate.
Replace the needle plate, or consult your
authorized dealer.
65
There are scratches near the hole in the presser
foot.
Replace the presser foot, or consult your
authorized dealer.
37
There are scratches on the race. Replace the race, or consult your authorized
dealer.
236
Bobbin thread breaks Bobbin is set incorrectly. Reset the bobbin thread correctly. 26
There are scratches on the bobbin or it doesnt
rotate properly.
Replace the bobbin. 26
Thread is twisted. Use scissors, etc. to cut the twisted thread
and remove it from the race, etc.
Skipped stitches Machine is threaded incorrectly. Check the steps for threading the machine
and rethread it correctly.
29
Using improper needle or thread for the
selected fabric.
Check the Fabric/Thread/Needle
Combination chart.
41
Needle is turned, bent or the point is dull. Replace the needle. 39
Needle is installed incorrectly. Reinstall the needle correctly. 39
Needle is defective. Replace the needle. 39
Dust or lint has collected under the needle plate. Remove the dust or lint with the brush. 236
Fabric puckers There is a mistake in the upper or bobbin
threading.
Check the steps for threading the machine
and rethread it correctly.
26, 29
Spool cap is set incorrectly. Check the method for attaching the spool cap,
then reattach the spool cap.
29
Using improper needle or thread for the
selected fabric.
Check the Fabric/Thread/Needle
Combination chart.
41
Needle is turned, bent or the point is dull. Replace the needle. 39
Stitches are too long when sewing thin fabrics. Shorten the stitch length. 49
Thread tension is set incorrectly. Adjust the thread tension. 50, 174
Wrong presser foot. Use the correct presser foot. STITCH SETTING
CHART
High-pitched sound
while sewing
Dust or lint is caught in the feed dogs. Remove the dust or lint. 236
Pieces of thread are caught in the race. Clean the race. 236
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
29
There are scratches on the race. Replace the race, or consult your authorized
dealer.
236
Cannot thread the
needle
Needle is not in the correct position. Press the Needle Position button to raise the
needle.
3
Threading hook does not pass through the eye
of the needle.
Press the Needle Position button to raise the
needle.
3
Needle is installed incorrectly. Reinstall the needle correctly. 39
252


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 4500D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 4500D in the language / languages: English as an attachment in your email.

The manual is 9,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 4500D

Brother Innov-is 4500D Quick start guide - English, German, Dutch, French, Italian, Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info