613440
160
Zoom out
Zoom in
Previous page
1/168
Next page
APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
158
Error messages
If (“Start/Stop” button) is pressed before the sewing machine is correctly set up or if an operation is
performed incorrectly, an error message appears in the LCD. Follow the instructions that appear. The message
will disappear if (OK key) or (Cancel/clear key) is pressed while the message is displayed.
Error Message Probable Cause
The selected setting cannot be changed with the selected pattern.
The “Start/Stop” button was pressed without connecting the foot
controller while the setting for adjusting the stitch width using the
sewing speed controller is set to [ON].
The stitch mode was changed.
This message appears when the current pattern is to be deleted.
The “Start/Stop” button was pressed while the foot controller was
connected.
A stitch other than the buttonhole, bar tack or darning stitch was
selected and the “Start/Stop” button was pressed while the buttonhole
lever is lowered.
The buttonhole, bar tack or darning stitch was selected and the “Start/
Stop” button was pressed while the buttonhole lever is raised.
The “Start/Stop” button, “Reverse/Reinforcement Stitch” button or
“Thread Cutter” button was pressed while the presser foot was raised.
You tried to combine more than 70 decorative stitches, stain stitches,
cross stitches or combined utility stitches.
The twin needle setting is selected while a pattern that cannot be sewn
with the twin needle is selected.
The “Reverse/Reinforcement Stitch” button, “Needle Position” button
or “Thread Cutter” button was pressed while the bobbin winder shaft is
moved to the right.
A pattern is being saved. Otherwise, the stitch settings are being saved.
The “Start/Stop” button or “Reverse/Reinforcement Stitch” button was
pressed after a stitch has been deleted.
The motor locked up because the thread is tangled.
The bobbin winder is winding the bobbin.
F01~F09
If error message “F01” through “F09” appears in the LCD while the
sewing machine is being used, the machine may be malfunctioning.
Contact your nearest authorized service center.
160


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 410 in the language / languages: English as an attachment in your email.

The manual is 5,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 410

Brother Innov-is 410 Quick start guide - All languages - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info