613570
112
Zoom out
Zoom in
Previous page
1/116
Next page
APPENDIX
110
Error Messages
If the sewing machine is incorrectly operated or if the sewing machine malfunctions, an error message appears
in the LCD.
The message can be cleared by pressing any key in the operation panel, turning any dial, or performing the
operation correctly.
If error message “F1” through “F9” appears in the LCD while the sewing machine is being used, the
machine may be malfunctioning. Contact your dealer or the nearest authorized service center.
Error Message
(in LCD)
Probable Cause Remedy
The start/stop button or the reverse/reinforcement
stitch button was pressed (The foot controller was
depressed if it is connected.) while the presser foot is
raised.
Lower the presser foot
before continuing the opera-
tion.
A stitch other than the buttonhole or bar tack stitch
was selected and the start/stop button was pressed
(The foot controller was depressed if it is connected.)
while the buttonhole lever is lowered.
Raise the buttonhole lever
before continuing the opera-
tion.
The buttonhole or bar tack stitch was selected and
the start/stop button was pressed (The foot controller
was depressed if it is connected.) while the button-
hole lever is raised.
Lower the buttonhole lever
before continuing the opera-
tion.
The reverse/reinforcement stitch button or needle
position button was pressed while the bobbin winder
shaft is moved to the right.
Move the bobbin winder
shaft to the left before con-
tinuing the operation.
The start/stop button was pressed, even though the
foot controller is connected.
Disconnect the foot
controller, and then press the
start/stop button. Otherwise,
operate the machine by
using the foot controller.
The motor locked up because the thread is tangled.
Turn off the machine and
remove the tangled thread
before continuing the opera-
tion.
The needle mode selection key was pressed to select
twin needle sewing while a stitch that cannot be
used with the twin needle is selected.
Select a stitch that can be
used with the twin needle.
The pattern selection dial was turned to select a pat-
tern while the twin needle setting is selected.
Cancel the twin needle set-
ting, and then select a stitch.
112


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 30 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 30

Brother Innov-is 30 User Manual - German - 116 pages

Brother Innov-is 30 User Manual - Dutch - 108 pages

Brother Innov-is 30 User Manual - French - 108 pages

Brother Innov-is 30 Quick start guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info