613570
105
Zoom out
Zoom in
Previous page
1/116
Next page
103
4
q
Attach the needle plate cover according to
steps i in “Cleaning the race” (page 96).
r
Check the condition of the needle, and then
install it.
If the needle is in a poor condition, for
example, if it is bent, be sure to install a new
needle.
Refer to “Checking the needle” (page 31)
and “Replacing the needle” (page 31).
Note
After completing this procedure, continue
with the following procedure in “Checking
machine operations” to check that the
machine is operating correctly.
Memo
Since the needle may have been damaged
when the fabric was caught in the machine,
we recommend replacing it with a new one.
Checking machine operations
If the needle plate has been removed, check
machine operations to confirm that installation
has been completed correctly.
a
Turn on the machine.
b
Select .
Note
Do not yet install the presser foot and
thread.
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to
check that the needle falls at the center of the
hole in the needle plate.
If the needle contacts the needle plate, remove
the needle plate, and then install it again,
starting with step
m in “Removing the fabric
from the machine” (page 102).
a Hole in the needle plate
b Handwheel
d
Select zigzag stitch . At this time, increase
the stitch length and width to their maximum
settings.
For details on changing the settings, refer to
“Adjusting the stitch length and width”
(page 42).
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle
bar and feed dogs operate correctly.
If the needle or feed dogs contact the needle
plate, the machine may be malfunctioning;
therefore, contact your nearest authorized
service center.
f
Turn off the machine, and then install the
bobbin and presser foot.
Refer to “Installing the bobbin” (page 18)
and “Replacing the presser foot” (page 33).
Never use a bobbin case that is scratched,
otherwise the upper thread may become
tangled, the needle may break or sewing
performance may suffer. For a new bobbin
case (part code: XE7560-001), contact your
nearest authorized service center.
Make sure that you fit the bobbin case
properly, otherwise the needle may break.
Never use bent needles. Bent needles can
easily break, possibly resulting in injuries.
CAUTION
CAUTION
105


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 30 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 30

Brother Innov-is 30 User Manual - German - 116 pages

Brother Innov-is 30 User Manual - Dutch - 108 pages

Brother Innov-is 30 User Manual - French - 108 pages

Brother Innov-is 30 Quick start guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info