631175
16
Zoom out
Zoom in
Previous page
1/68
Next page
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
14
Memo
When the sewing machine is started or the
handwheel is turned after winding the
thread around the bobbin, the machine will
make a clicking sound; this is not a
malfunction.
The needle bar does not move when you
slide the bobbin winding shaft to the right.
Lower threading
Install the bobbin wound with thread.
For more details on quick-set bobbin, see page 15.
a
Raise the needle to its highest position by turning
the handwheel toward you (counterclockwise) or
press (needle position button) (for models
equipped with the needle position button), and
raise the presser foot lever.
b
Slide the button and open the cover.
a Cover
b Slide button
c
Put the bobbin in so the thread comes out in
the direction shown by the arrow.
Only use bobbins that were designed to be
used with this machine.
d
Hold the end of the thread, push the bobbin
down with your finger, and then pass the
thread through the slit, as shown.
Make sure that the thread is correctly
inserted through the tension-adjusting spring
of the bobbin case. If it is not inserted, re-
insert the thread.
a Tension-adjusting spring
e
Replace the bobbin cover. Put the left tab in
place (see arrow a), and then press lightly on
Winding the bobbin improperly may cause
the thread tension to loosen, breaking the
needle and resulting in injury.
a Wound evenly
b Wound poorly
The bobbin was designed specifically for this
sewing machine. If bobbins from other
models are used, the machine will not operate
correctly. Use only the enclosed bobbin or
bobbins of the same type (part code: SA156,
SFB: XA5539-151).
Make sure you turn the power off while
threading the machine. If you accidentally
step on the foot controller and the machine
starts to sew, you could be injured.
CAUTION
1
2
Actual size
This model Other models
11.5 mm
(7/16 inch)
CAUTION
Make sure you set the bobbin so the thread
unrolls in the right direction. If the thread unrolls
in the wrong direction, it may cause the thread
tension to be incorrect or break the needle.
12
CAUTION
1
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother ES-2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother ES-2000 in the language / languages: English as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother ES-2000

Brother ES-2000 User Manual - German - 66 pages

Brother ES-2000 User Manual - Dutch - 66 pages

Brother ES-2000 User Manual - French - 66 pages

Brother ES-2000 User Manual - Spanish - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info