456633
45
Zoom out
Zoom in
Previous page
1/100
Next page
43
2
If thick seams are being sewn and the fabric does
not feed at the beginning of stitching
The fabric may not feed when thick seams are
being sewn and the presser foot is not level, as
shown below. In this case, use the presser foot
locking pin (black button on the left side of zigzag
foot “J”) so that the presser foot remains level
while sewing, allowing the fabric to be fed
smoothly.
a Sewing direction
a
Raise the presser foot lever.
b
Align the beginning of stitching, and then
position the fabric.
c
While holding zigzag foot “J” level, hold the
presser foot locking pin (black button on the
left side) pressed in, and lower the presser
foot lever.
a Presser foot locking pin (black button)
d
Release the presser foot locking pin (black
button).
X The presser foot remains level, allowing
the fabric to be fed.
After the seam is sewn, the presser foot will
return to its original angle.
Sewing hook-and-loop
fastener
Note
Before start sewing, baste together the fabric
and the hook-and-loop fastener.
Make sure that the needle passes through the hook-
and-loop fastener by turning the handwheel and
lower the needle into the hook-and-loop fastener
before sewing. And then, sew the edge of the hook-
and-loop fastener at a slow speed.
If the needle does not pass through the hook-and-
loop fastener, replace the needle with the needle for
thick fabrics (
page 28
).
a Edge of the hook-and-loop fastener
If fabric more than 6 mm (15/64 inch) thick is
sewn or if the fabric is pushed with too much
force, the needle may bend or break.
Use only the ungummed hook-and-loop
fastener which is for sewing. If the glue is
attached to the needle or the bobbin hook
race, it may cause malfunction.
If the hook-and-loop fastener is sewn with the
thin needle (65/9-75/11), the needle may
bend or break.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother DS 120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother DS 120 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother DS 120

Brother DS 120 User Manual - English, German - 104 pages

Brother DS 120 User Manual - Dutch - 104 pages

Brother DS 120 User Manual - Dutch - 2 pages

Brother DS 120 User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info