456633
18
Zoom out
Zoom in
Previous page
1/100
Next page
16
KNOWING YOUR SEWING MACHINE
g
Pull the thread to the right, pass it under the
hook of the bobbin-winding thread guide, and
then wind the thread counterclockwise
between the discs, pulling it in as far as
possible.
a Bobbin-winding thread guide
Make sure that the thread passes under the
pretension disk.
b Hook
c Pretension disk
d Pull it in as far as possible.
Note
Make sure that the thread is pulled as far as
possible into the pretension disk, otherwise
the bobbin may not be wound cleanly.
h
Put the bobbin onto the bobbin winder shaft
and slide the bobbin winder shaft to the right.
Turn the bobbin clockwise, by hand, until the
spring on the shaft slides into the notch in the
bobbin.
Make sure to pull out 7 to 10 cm (2-3/4 to
3-15/16 inches) of thread from the hole on
the bobbin.
a Spring on the shaft
b Notch
c 7-10 cm (2-3/4 – 3-15/16 inches)
i
Turn on the sewing machine.
j
While holding the end of the thread, gently
press the foot controller or press (start/
stop button) (for models equipped with the
start/stop button) to wind the thread around
the bobbin a few times. Then stop the
machine.
Note
If the sewing machine is to be operated
using the foot controller, connect the foot
controller before turning on the machine.
When the foot controller is plugged in, the
start/stop button cannot be used to start
sewing (only for models equipped with the
start/stop button).
k
Trim the excess thread above the bobbin.
Pull the thread taut and hold the end of the
thread straight up. If the thread is too short,
not pulled taut or held at an angle, injuries
may occur when the thread is wound around
the bobbin.
Make sure you follow the instructions
carefully. If you do not cut the thread
completely, and the bobbin is wound, when
the thread runs low it may tangle around the
bobbin and cause the needle to break.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother DS 120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother DS 120 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother DS 120

Brother DS 120 User Manual - English, German - 104 pages

Brother DS 120 User Manual - Dutch - 104 pages

Brother DS 120 User Manual - Dutch - 2 pages

Brother DS 120 User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info