451186
42
Zoom out
Zoom in
Previous page
1/51
Next page
Installing the Driver & Software
40
STEP2
Macintosh
®
Macintosh
®
Wireless
Network
6 Enter the SSID you wrote down in step 1 using
a, b and OK keys to choose each letter or
number. You can use the and keys to
move the cursor left and right. For example, to
enter the letter a, press the a key once. To
enter the number 3, hold down the a key until
it appears.
The letters appear in this order: lower case,
upper case, numbers and then special letters.
(For more information, see Entering Text on
page 46.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings.
7 Press a or b to choose Infrastructure,
then press OK.
8 Use the a, b and OK keys to choose one of
the options below: If your network is configured
for Authentication and Encryption you must
match the settings used for your network.
No Authentication or Encryption: Choose
Open System, press OK then choose None
for Encryption Type and press OK. Then
press to choose Yes to apply your settings.
Go to step 11.
No Authentication with WEP Encryption:
Choose Open System, press OK then use the
a or b to choose WEP for the
Encryption Type and press OK. Go to
step 9.
Authentication with WEP Encryption:
Choose Shared Key, press OK. Go to step 9.
Authentication with WPA/WPA2-PSK (TKIP
or AES) Encryption: Choose WPA/WPA2-
PSK, press OK. Go to step 10.
9 Choose the appropriate key number and press
OK. Enter the WEP key you wrote down in
step 1 using a, b and OK keys to choose
each letter or number. You can use the
and keys to move the cursor left and right.
For example, to enter the letter a, press the a
key once. To enter the number 3, hold down
the a key until it appears.
The letters appear in this order: lower case,
upper case, numbers and then special letters.
(For more information, see Entering Text on
page 46.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings. Go to step 11.
Most access points and routers can store
more than one key, but they will only use
one at any time for authentication and
encryption.
10 Press a or b to choose TKIP or AES for
Encryption Type and press OK.
Enter the WPA/WPA2-PSK password you
wrote down in step 1 using a, b and OK keys
to choose each letter or number. You can use
the and keys to move the cursor left
and right. For example, to enter the letter a,
press the a key once. To enter the number 3,
hold down the a key until it appears.
The letters appear in this order: lower case,
upper case, numbers and then special letters.
(For more information, see Entering Text on
page 46.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings. Go to step 11.
11 Your machine will now try to connect to your
wireless network using the information you
have entered. If successful, Connected will
appear briefly on the LCD.
If your machine does not successfully connect
to your network, you should repeat steps 3 to
10 to make sure you have entered the correct
information.
If your access point does not have DHCP
enabled you will need to manually configure
the IP address, subnet mask and gateway of
the machine to suit your network. See the
Network User’s Guide for details.
Wireless setup is now complete. A four
level indicator on the bottom of your
machine’s LCD will show the wireless
signal strength of your access point or
router. To install the MFL-Pro Software
suite, continue to step 12.
12 Turn on your Macintosh
®
.
13 Put the supplied CD-ROM into your CD-ROM
drive.
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother DCP-750CW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother DCP-750CW in the language / languages: English as an attachment in your email.

The manual is 4,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother DCP-750CW

Brother DCP-750CW User Manual - English - 113 pages

Brother DCP-750CW Installation Guide - German - 53 pages

Brother DCP-750CW User Manual - German - 119 pages

Brother DCP-750CW Installation Guide - Dutch - 52 pages

Brother DCP-750CW User Manual - Dutch - 119 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info