451174
25
Zoom out
Zoom in
Previous page
1/38
Next page
25
For Wireless Network Users
Wireless Network
12
Configure the wireless
settings using the
automatic wireless (one-
push) method
a Confirm your wireless access point/router has
the SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™ symbol as shown below.
b Place the Brother machine within range of your
SecureEasySetup™, Wi-Fi Protected Setup or
AOSS™ access point/router. The range may
differ depending on your environment. Refer to
the instructions provided with your access
point/router.
c Push the SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™ button on your wireless
access point/router.
See the user’s guide for your wireless access
point/router for instructions.
d On your machine, press Menu.
Press a or b to choose 3.Network and press
OK.
Press a or b to choose 2.WLAN and press OK.
Press a or b to choose 3.SES/WPS/AOSS and
press OK.
When Change to WLAN? is displayed, press
a to accept.
This will start the wireless setup wizard.
This feature will automatically detect which
mode (SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™) your access point/router
uses to configure your machine.
e If the LCD shows Connected, the machine
has successfully connected to your wireless
access point/router. You can now use your
machine in a wireless network.
If the LCD shows Setting WLAN, then
Connection Error, a session overlap was
detected. The machine has detected 2 or more
wireless access points/routers on your network
that have the SecureEasySetup™, Wi-Fi
Protected Setup mode or AOSS™ mode
enabled. Make sure that only one wireless
access point/router has one of these modes
enabled and try starting from c again.
If the LCD shows Setting WLAN, then No
Access Point, the machine has not detected
the access point/router on your network with
the SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™ mode enabled. Move your
machine close to the access point/router and
try starting from c again.
If the LCD shows Setting WLAN, then
Connection Fail, the machine has not
successfully connected to your wireless access
point/router. Try starting from c again. If the
same message is indicated again, reset the
machine back to the default factory settings
and try again. For resetting, see Restore the
network settings to factory default on page 37.
f Press OK.
Note
If your wireless access point/router supports
Wi-Fi Protected Setup (PIN Method) and you
want to configure your machine using the PIN
(Personal Identification Number) Method, see
Using the PIN Method of Wi-Fi Protected Setup in
the Network User’s Guide on the CD-ROM.
LCD messages when using the
SES/WPS/AOSS control panel menu
Setting WLAN Searching for or accessing the
access point, and
downloading settings from the
access point.
Connecting
SES/WPS/AOSS
Connecting to the access
point.
Connected The machine has successfully
connected.
Connection
Error
A session overlap was
detected.
No Access
Point
The access point detection
failed.
Connection
Fail
Connection failed.
The machine was not able to
connect with the access point.
Try the configuration from c on
page 25 again.
Note
You can also manually configure the wireless
settings following the steps starting at step 11-a
on page 23.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother DCP-377CW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother DCP-377CW in the language / languages: English as an attachment in your email.

The manual is 6,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother DCP-377CW

Brother DCP-377CW Installation Guide - English - 2 pages

Brother DCP-377CW User Manual - English - 117 pages

Brother DCP-377CW Installation Guide - German - 38 pages

Brother DCP-377CW Installation Guide - German - 2 pages

Brother DCP-377CW User Manual - German - 119 pages

Brother DCP-377CW Installation Guide - Dutch - 38 pages

Brother DCP-377CW Installation Guide - Dutch - 2 pages

Brother DCP-377CW User Manual - Dutch - 119 pages

Brother DCP-377CW Installation Guide - French - 38 pages

Brother DCP-377CW Installation Guide - French - 2 pages

Brother DCP-377CW User Manual - French - 121 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info