718826
12
Zoom out
Zoom in
Previous page
1/60
Next page
10
KNOWING YOUR SEWING MACHINE
f
While holding the end of the thread, gently
press the foot controller or press (start/stop
button) (for models equipped with the start/stop
button) to wind the thread around the bobbin a
few times. Then stop the machine. Then stop the
machine and trim the excess thread.
Note
If the sewing machine is to be operated using the
foot controller, connect the foot controller before
turning on the machine.
When the foot controller is plugged in, the start/
stop button cannot be used to start or stop sewing
(only for models equipped with the start/stop
button).
g
Slide the sewing speed controller to the right (to
set the speed to fast). (For models equipped with
the sewing speed controller.)
h
Press the foot controller or press (start/stop
button) (for models equipped with the start/stop
button) to start.
i
When the bobbin seems full and begins spinning
slowly, take your foot off the foot controller or
press (start/stop button) (for models
equipped with the start/stop button).
j
Cut the thread, slide the bobbin winder shaft to
the left and remove the bobbin.
k
Slide the sewing speed controller back to its
original position (for models equipped with the
sewing speed controller).
Memo
When the sewing machine is started or the
handwheel is turned after winding the thread
around the bobbin, the machine will make a
clicking sound; this is not a malfunction.
The needle bar does not move when you slide the
bobbin winding shaft to the right.
For models equipped with the fast bobbin
winding system
a
Follow steps 1 through 2 of the procedure in
“Winding the bobbin” to pass the thread around
the pre-tension disk (page 9).
b
Place the bobbin on the bobbin winder shaft so
that the spring on the shaft fits into the notch in
the bobbin. Then slide the bobbin winder shaft
to the right.
a Notch
b Spring
CAUTION
Make sure you follow the instructions carefully.
If you do not cut the thread completely, and the
bobbin is wound, when the thread runs low it
may tangle around the bobbin and cause the
needle to break.
1 Sewing speed controller
CAUTION
Not winding the bobbin properly may cause the
thread tension to loosen, and may break the
needle.
a Wound evenly
b Wound poorly
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother CS70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother CS70 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother CS70

Brother CS70 Quick start guide - English, German - 2 pages

Brother CS70 User Manual - German - 60 pages

Brother CS70 Quick start guide - Dutch - 2 pages

Brother CS70 User Manual - Dutch - 60 pages

Brother CS70 Quick start guide - French - 2 pages

Brother CS70 User Manual - French - 60 pages

Brother CS70 Quick start guide - Italian, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info