613411
15
Zoom out
Zoom in
Previous page
1/68
Next page
13
1
For models equipped with the fast bobbin
winding system
a
Follow steps 1 through 2 of the procedure in
“Winding the bobbin” to pass the thread
around the pre-tension disk (page 11).
b
Place the bobbin on the bobbin winder shaft
so that the spring on the shaft fits into the
notch in the bobbin.
a Notch
b Bobbin winder shaft spring
c
Slide the bobbin winder shaft to the right.
d
While holding the thread that wraps around the
pre-tension disk with your left hand, use your
right hand to wind the free end of the thread
clockwise around the bobbin five or six times.
e
Pull the thread to the right and pass it through
the slit in the bobbin winder seat.
a Slit in bobbin winder seat (with built-in cutter)
X The thread is cut to a suitable length.
f
Slide the sewing speed controller to the right
(to set the speed to fast) (for models equipped
with the sewing speed controller).
a Sewing speed controller
g
Turn on the sewing machine.
h
Press the foot controller or press (start/
stop button) (for models equipped with the
start/stop button) to start.
Note
If the sewing machine is to be operated
using the foot controller, connect the foot
controller before turning on the machine.
When the foot controller is plugged in, the
start/stop button cannot be used to start or
stop sewing (only for models equipped with
the start/stop button).
i
When the bobbin begins spinning slowly, take
your foot off the foot controller or press
(start/stop button) (for models equipped with
the start/stop button).
j
Cut the thread, slide the bobbin winder shaft
to the left and remove the bobbin.
k
Slide the sewing speed controller back to its
original position (for models equipped with
the sewing speed controller).
Be sure to cut the thread as described. If the bobbin is
wound without cutting the thread using the cutter built
into the slit in the bobbin winder seat, the thread may
become tangled in the bobbin or the needle may bend
or break when the bobbin thread starts to run out.
CAUTION
Not winding the bobbin properly may cause the
thread tension to loosen, and may break the needle.
a Wound evenly
b Wound poorly
CAUTION
1
2
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother CS6000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother CS6000 in the language / languages: English as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother CS6000

Brother CS6000 Quick start guide - English, German, Dutch, French, Italian, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info