555762
64
Zoom out
Zoom in
Previous page
1/68
Next page
APPENDIX ————————————————————————————————————————————————————
62
ERROR MESSAGES
If an operation is performed incorrectly before the sewing machine is set up, an error message appears on the
operation panel. Follow the instructions indicated in the table.
If you press the stitch selection key or do the operation correctly while the error message is displayed, the
message disappears.
Note
If error message “F1” through “F8” appears in the LCD while the sewing machine is being used, the
machine may be malfunctioning. Contact your nearest authorized service center.
Operation beep (for models equipped with the operation beep)
Each time a key is pressed you will hear one beep. If a non-functioning key is pressed or an incorrect operation
is performed you will hear two or four beeps (only for models equipped with the operation beep).
If a key is pressed (correct operation)
One beep sounds.
If an incorrect operation is performed or a non-functioning key is pressed
Two or four beeps sound.
If the machine locks up, for example, because the thread is tangled
The sewing machine beeps for four seconds and the machine automatically stops. Be sure to check for the
cause of the error, and correct it before continuing to sew.
Error Message Probable Cause Solution
The foot controller was pressed (or the start/stop but-
ton was pressed if the foot controller is not con-
nected) and the reverse/reinforcement stitch button
was pressed while the presser foot is raised.
Lower the presser foot lever
before continuing the opera-
tion.
A stitch other than the buttonhole or bar tack stitch
was selected and the foot controller was pressed (or
the start/stop button was pressed if the foot controller
is not connected) while the buttonhole lever is low-
ered.
Raise the buttonhole lever
before continuing the opera-
tion.
The buttonhole or bar tack stitch was selected and
the foot controller was pressed (or the start/stop but-
ton was pressed if the foot controller is not con-
nected) while the buttonhole lever is raised.
Lower the buttonhole lever
before continuing the opera-
tion.
The reverse/reinforcement stitch button or needle
position button was pressed while the bobbin winder
shaft is moved to the right.
Move the bobbin winder
shaft to the left before con-
tinuing the operation.
The start/stop button was pressed while the foot con-
troller was connected.
Disconnect the foot control-
ler, and then press the start/
stop button. Otherwise,
operate the machine by
using the foot controller.
The motor locked up because the thread is tangled.
Remove the tangled thread
before continuing the opera-
tion.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother CS10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother CS10 in the language / languages: English as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother CS10

Brother CS10 User Manual - German - 68 pages

Brother CS10 User Manual - Dutch - 68 pages

Brother CS10 User Manual - French - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info