718772
15
Zoom out
Zoom in
Previous page
1/212
Next page
NAMES OF MACHINE PARTS
Getting Ready
13
1
Measurements on the needle plate, bobbin cover (with
mark) and needle plate cover
The measurements on the bobbin cover are references
for stitch patterns with a middle (center) needle
position. The measurements on the needle plate and the
needle plate cover are references for stitches with a left
needle position.
1 For stitches with a middle (center) needle position
2 For stitches with a left needle position
3 Left needle position on the needle plate <inch>
4 Left needle position on the needle plate <cm>
5 Middle (center) needle position on the bobbin cover
(with mark) <inch>
6 Left needle position on the needle plate cover <inch>
Operation Buttons
1 “Start/Stop” button
Press the “Start/Stop” button to start or stop the machine. The
button changes color according to the machine’s operation
mode.
2 Reverse stitch button
Press the reverse button to sew reverse or reinforcement
stitches depending on the selected stitch pattern. (page 59)
3 Reinforcement stitch button
Press the reinforcement button to sew a single stitch
repeatedly and tie-off. (page 59)
For character/decorative stitches, press this button to end with
a full stitch instead of at a mid-point.
The LED beside the button automatically lights up while the
stitch is being sewn and goes off when sewing is finished.
4 Needle position button
Press the needle position button to raise or lower the needle
position. Pressing the button twice sews a single stitch.
5 Thread cutter button
Press the thread cutter button after sewing to automatically
trim the excess thread.
6 Presser foot lifter button
Press the presser foot lifter button to lower the presser foot and
apply pressure to the fabric. Press this button again to raise the
presser foot.
7 Sewing Speed controller
Use the sewing speed controller to adjust the sewing speed.
Move the slide to the left to sew at slower speeds. Move the
slide to the right to sew at higher speeds.
8 Automatic threading button
Use the automatic threading button to automatically thread the
needle.
Green: The machine is ready or is operating.
Red: The machine is not ready.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Brother Innov-is XJ1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Brother Innov-is XJ1 in the language / languages: English as an attachment in your email.

The manual is 12,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Brother Innov-is XJ1

Brother Brother Innov-is XJ1 User Manual - German - 212 pages

Brother Brother Innov-is XJ1 User Manual - Dutch - 212 pages

Brother Brother Innov-is XJ1 User Manual - French - 212 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info