644490
245
Zoom out
Zoom in
Previous page
1/262
Next page
BE-1204B-BC • BE-1206B-BC 11-5
Chapter 11 Error code list
Code Error Measures
E-B2 Hook motor home position error
E-B3 Hook motor standby position error
E-B4 Hook motor motor mode error
E-B5 Hook motor communication error
E-B6 Hook motor parameter error
E-B7 Hook motor overheat error
E-B8 Hook motor overcurrent error
This is not displayed in this model.
E-B9 Thread trimming motor zero point error
Turn the power off and on once. If the same error occurs
again, the lower shaft motor is faulty.
E-BA Power supply frequency error
Turn the power off and check the thread trimmer and turn the
power on again. If it occurs again, the thread trimmer is faulty.
E-BC No power error
It may usually occur momentarily when turning off the machine.
If it occurs when the machine is on, it is a power failure
detection error.
E-BD Lower shaft flash memory error
E-BE Lower shaft version-up error
E-BB,
BF
Lower shaft motor undefined error
E-C1 Area over during embroidering
This is not displayed in this model.
E-C2 Wiper out error
If the wiper is tangled with a thread, remove it. Press the
or turn on the F/B switch on the head to either side.
E-C3 Embroidering data buffer empty
Check the connection of the communication cable of the panel.
If the cable is connected correctly , press the
or turn on
the F/B switch on the head to either side. If the cable is
disconnected , turn off the power and connect the cable.
E-C4 Presser foot down error
E-C5
Measured voltage value could not be received
form the lower shaft motor CPU.
E-C6
Voltage value could not be transferred to the
lower shaft motor CPU.
E-C7 Lower shaft error
E-C8 Hook motor home position error
E-C9 Embroidering start error
E-CA No sewing permisson
This is not displayed in this model.
E-CB Spindle rotation speed error
Press the
or turn on the F/B switch on the head to either
side to cancel the error and press the
. If the same error
occurs again, there is a possibility that the spindle is
overloaded.
E-CC Shuttle thread entanglement automatic reset This is not usually displayed.
E-CD Speed command can not be received.
Turn the power off and on once. If the same error occurs
again, the main PCB is faulty.
E-CE Cylinder bed position error
E-CF
Rated voltage value could not be received from
the lower shaft motor CPU.
This is not usually displayed.
E-D0 Power PC board error
Turn the power off and on once. If the same error occurs
again, the power PCB is faulty.
E-D1 Cooling fan motor stop. This is not usually displayed.
245


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother BE-1206B-BC PC control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother BE-1206B-BC PC control in the language / languages: English as an attachment in your email.

The manual is 7,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info