644489

Brother BE-1204B-BC - PC control Manual

244
Zoom out
Zoom in
Previous page
1/262
Next page
11-4 BE-1204B-BC • BE-1206B-BC
Chapter 11 Error code list
Code Error Measures
E-36 Needle overhang (-X, +Y)
E-38 Needle overhang (-Y)
E-39 Needle overhang (+X, -Y)
E-3C Needle overhang (-X, -Y)
Pattern or the needle position is out of the embroidering area.
Reset the embroidering area on the panel or move the hoop to
the sewable position.
E-40
The status of presser foot is issued as an alarm
when every second machine is used.
E-41 Invalid start-up error
This is not usually displayed.
E-42 XY movement error
Press the
or turn on the F/B switch on the head to either
side. If this error occurs frequently, check if the tension of the
pulley belt is proper.
E-43 I/F CPU failed to read EEPROM data
Turn the power off and on once. If the same error occurs
again, the main PC is faulty.
E-44
Failed in the communication with inter-head
CPU
Press the
or turn ON the F/B switch on the head to either
side. If the same error occurs again, the connector of
communication cable on the inter-head CPU may be
disconnected.
E-45 Failed in the communication with head CPU
Press the
or turn ON the F/B switch on the head to either
side. If the same error occurs again, the connector of
communication cable on the head CPU may be disconnected.
E-46 Failed in the communication with XY CPU
Press the
or turn ON the F/B switch on the head to either
side. If the same error occurs again, the main PCB is faulty.
E-47 Failed in the communication with I/F CPU
Press the
or turn ON the F/B switch on the head to either
side. If the same error occurs again, the main PCB is faulty.
E-48 The main shaft rotated the opposite way
Turn OFF the power and check if the sensors of the encoder A
and B are connected correctly, not mixed-up each other. If
those connections are correct, then check if the pin connections
of the main shaft motor connectors are correct.
E-49 Can not identify the machine model
Turn OFF the power, check if the model identification harness is
connected properly, and turn ON the power again.
E-4A Failed in the communication with I/O CPU
Press the
or turn ON the F/B switch on the head to either
side. If the same error occurs again, the connector of
communication cable on the I/O PCB may be disconnected.
E-A1 Spindle motor lock
Press the
or turn on the F/B switch on the head to either
side. If it occurs frequently, the main shaft mechanism is
faulty.
E-A2 Main PC board temperature too high
E-A3 Spindle motor voltage too low
E-A4 Spindle motor voltage too high
E-A5 Spindle motor CPU error
E-A6
Spindle motor CPU communication command
error
E-A7 Spindle motor CPU send/receive error
This is not usually displayed.
E-A8 Spindle stop position signal error
Adjust the pulley stop position (100 °) above the needle and
press the
. If the error occurs frequently, the parts related
to the main shaft stop position sensor are faulty.
E-A9 Spindle CPU parameter error
E-B0 Lower shaft CPU error
E-B1 Thread tangle in rotary hook
This is not displayed in this model.
… 244 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother BE-1204B-BC - PC control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother BE-1204B-BC - PC control in the language / languages: English as an attachment in your email.

The manual is 7,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info