463776
33
Zoom out
Zoom in
Previous page
1/76
Next page
31
English
5. Set the stitch length control lever.
- Tapes: between "3" and "4"
- Elastics: "4"
6. Adjust the presser adjusting dial 2
- at "0" when sewing with tapes.
- at desirable number for contraction when
sewing with elastics.
NOTE:
Contraction will be increased with larger number.
7. Make trial sewing and adjust thread tensions.
Example of proper sewing seam:
<B>
<A>
<C>
<D>
<A> Surface
<B> Tape
<C> Surface
<D> Elastic
NOTE:
Thread tensions are alike to normal overedging
when sewing with tapes.
It is recommendable to have a stronger tension for
under looper and over looper for beautiful finish.
It is advisable to make trial sewing on each material
/ thread due to different contraction.
Pearl sequence foot
Features
By using the pearl sequence foot, you can bead
on fabric. It is useful for decorated edge of curtain,
table cloth, dress, etc. From 3mm to 5mm
sequential pearl can be sewn with this foot.
LS
Preparation
1. Retract the knife (see CHAPTER 1 "Retracting
knife").
2. Attach the pearl sequence foot (see CHAPTER
1 "Attaching/ Removing presser foot").
3. Set up the machine for 3 thread overlock stitch
with one needle in the left position.
The right needle should be removed.
How to adjust the machine
1. Adjust the stitch length according to the length
as <A> or <B>. For example, 4mm stitch
length means 4mm for <A> or <B>.
<A>
<B>
<A>
<B>
2. Adjust stitch width 3 to 5mm.
3. Adjust thread tension as follows:
Needle thread: slightly decrease
Over looper thread: slightly decrease
Under looper thread: slightly increase
How to set fabric and pearl
1 ~ 1.5mm
1
2
3
1. Fold the fabric according to the line for pearl
fitting.
2. Place the fabric at needle dropping point
keeping the folded edge with guide 1.
3. Use the screw 2 and adjust the clearance
between folded edge needle so that it
becomes 1mm to 1.5mm.
4. Place the pearl through the guide just front of
guide tunnel 3.
Test sewing
1. Sew turning hand wheel by hand until the pearl
comes through the tunnel.
2. Sew at slow speed while guiding the pearl and
fabric by hand.
3. Tie both end of thread at the beginnig and end.
NOTE:
Thread tension is easy to loosen especially for small
size pearl. Retract movable stitch tongue for better
stitching.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother 3034D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother 3034D in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother 3034D

Brother 3034D User Manual - German - 76 pages

Brother 3034D User Manual - Dutch, French - 76 pages

Brother 3034D User Manual - Italian - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info